- 您现在的位置：买卖IC网 > PDF目录98161 > TAS5110DAP (TEXAS INSTRUMENTS INC) 50 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32 PDF资料下载
参数资料
| 型号： | TAS5110DAP |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 50 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32 |
| 封装： | PLASTIC, HTSSOP-32 |
| 文件页数： | 20/20页 |
| 文件大小： | 336K |
| 代理商： | TAS5110DAP |
TAS5110
SLES028A MAY 2002 REVISED SEPTEMBER 2002
9
www.ti.com
device operation
power sequences
system power-up/power-down sequencing
The recommended power-up/power-down sequence is shown in Figure 3. For proper operation the RESET
signal should be kept low when both DVDD and output power (PVDDA1, PVDDA2, PVDDB1, and PVDDB2)
are being applied. The RESET signal should remain low for at least 1 ms after output power is applied.
> 1 ms
DVDD
PWDN
PVDDA2
PVDDB2
RESET
> 1 ms
> 100
s
> 100
s
PVDDA1
PVDDB1
For most applications, it is recommended that the PWDN pin be connected directly to the DVDD pin.
Figure 3. Power-Up/Power-Down Sequence
RESET function
The device is put into a reset condition when the (active low) RESET signal is asserted. While in the reset state,
the input H-bridge control signals consisting of PWM_AP, PWM_AM, PWM_BP, and PWM_BM are ignored, and
the H-bridge MOSFETs are placed in a state where OUTPUTA and OUTPUTB are both low. Asserting the
RESET signal low also causes the short circuit protection latch to be reset. The RESET signal is normally
connected to the VALID signal from the TAS50xx.
reinitialization sequence
Proper initial conditions for this device include asserting the RESET signal until the reset operation has
completed (1 ms). Additionally, when using this device with the TAS50xx controller, this function can be
accomplished by asserting the reset pin on the TAS50xx during the reset sequence (see Figure 3).
audio application considerations
optimal power transfer for H-bridge
The TAS5110 is a power H-bridge that is designed to deliver a maximum of 50 W RMS into a 6-
load. In order
to achieve 50 W into 6
, the system designer must provide an adequate thermal design. See the Thermal
Methodology for the 32-Pin DAD Package 50 W, 6-
Test and the Thermal Methodology for the 32-Pin DAP
Package 50 W, 6-
sections for a discussion of possible thermal solutions. Careful attention must be given to
the value of the high-voltage power supply level for a given load resistance. See recommended operating
conditions. See the Maximum Available Power at Common Load Impedances for Both DAP and DAD Packages
section.
相关PDF资料 |
PDF描述 |
|---|---|
| TAS5110IDAP | 50 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32 |
| TAS5110DADR | 50 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32 |
| TAS5110DAPR | 50 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32 |
| TAS5110IDAPR | 50 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32 |
| TAS5110DADRG4 | 50 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TAS5110DAPR | 功能描述:音频放大器 Dig Amp Power Stage RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TAS5110DAPRG4 | 功能描述:音频放大器 Dig Amp Power Stage RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TAS5110IDAD | 制造商:TI 制造商全称:Texas Instruments 功能描述:TRUE DIGITAL AUDIO AMPLIFIER TAS5110 PWM POWER OUTPUT STAGE |
| TAS5110IDADR | 制造商:TI 制造商全称:Texas Instruments 功能描述:TRUE DIGITAL AUDIO AMPLIFIER TAS5110 PWM POWER OUTPUT STAGE |
| TAS5110IDAP | 制造商:TI 制造商全称:Texas Instruments 功能描述:TRUE DIGITAL AUDIO AMPLIFIER TAS5110 PWM POWER OUTPUT STAGE |
发布紧急采购，3分钟左右您将得到回复。