- 您现在的位置：买卖IC网 > PDF目录98161 > TAS5112ADCA (TEXAS INSTRUMENTS INC) 62 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO56 PDF资料下载
参数资料
| 型号： | TAS5112ADCA |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 62 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO56 |
| 封装： | GREEN, PLASTIC, HTSSOP-56 |
| 文件页数： | 6/29页 |
| 文件大小： | 762K |
| 代理商： | TAS5112ADCA |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
TAS5112A
SLES094B - OCTOBER 2003 - REVISED JUNE 2008
www.ti.com
14
In practice this means that the DVDD-to-PWM processor
(front-end) should be stable and initialization should be
completed before RESET is de-asserted to the back end.
CONTROL I/O
Shutdown Pin: SD
The SD pin functions as an output pin and is intended for
protection-mode signaling to, for example, a controller or
other front-end device. The pin is open-drain with an
internal pullup resistor to DVDD.
The logic output is, as shown in the following table, a
combination of the device state and RESET input:
SD
RESET
DESCRIPTION
0
Reserved
0
1
Device in protection mode, i.e., UV and/or OC
and/or OT error
1(2)
0
Device set high-impedance (Hi-Z), SD forced high
1
Normal operation
(2) SD is pulled high when RESET is asserted low independent
of chip state (i.e., protection mode). This is desirable to
maintain compatibility with some TI PWM front ends.
Temperature Warning Pin: OTW
The OTW pin gives a temperature warning signal when
temperature exceeds the set limit. The pin is of the
open-drain type with an internal pullup resistor to DVDD.
OTW
DESCRIPTION
0
Junction temperature higher than 125
°C
1
Junction temperature lower than 125
°C
Overall Reporting
The SD pin, together with the OTW pin, gives chip state
information as described in Table 1.
Table 1. Error Signal Decoding
OTW
SD
DESCRIPTION
0
Overtemperature error (OTE)
0
1
Overtemperature warning (OTW)
1
0
Overcurrent (OC) or undervoltage (UV) error
1
Normal operation, no errors/warnings
Chip Protection
The TAS5112A protection function is implemented in a
closed loop with, for example, a system controller and TI
PWM processor. The TAS5112A contains three individual
systems protecting the device against error conditions. All
of the error events covered result in the output stage being
set in a high-impedance state (Hi-Z) for maximum
protection of the device and connected equipment.
The device can be recovered by toggling RESET low and
then high, after all errors are cleared.
Overcurrent (OC) Protection
The device has individual forward current protection on
both high-side and low-side power stage FETs. The OC
protection works only with the demodulation filter present
at the output. See Demodulation Filter Design in the
Application Information section of the data sheet for design
constraints.
Overtemperature (OT) Protection
A dual temperature protection system asserts a warning
signal when the device junction temperature exceeds
125
°C. The OT protection circuit is shared by all
half-bridges.
Undervoltage (UV) Protection
Undervoltage lockout occurs when GVDD is insufficient
for proper device operation. The UV protection system
protects the device under power-up and power-down
situations. The UV protection circuits are shared by all
half-bridges.
Reset Function
The reset has two functions:
D Reset is used for re-enabling operation after a
latching error event.
D Reset is used for disabling output stage
switching (mute function).
The error latch is cleared on the falling edge of reset and
normal operation is resumed when reset goes high.
PROTECTION MODE
Autorecovery (AR) After Errors (PMODE0)
In autorecovery mode (PMODE0) the TAS5112A is
self-supported in handling of error situations. All protection
systems are active, setting the output stage in the
high-impedance state to protect the output stage and
connected equipment. However, after a short time period
the device autorecovers, i.e., operation is automatically
resumed provided that the system is fully operational.
The autorecovery timing is set by counting PWM input
cycles, i.e., the timing is relative to the switching frequency.
The AR system is common to both half-bridges.
相关PDF资料 |
PDF描述 |
|---|---|
| TAS5112ADFDRG4 | 62 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO56 |
| TAS5112ADFDR | 62 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO56 |
| TAS5112ADFDG4 | 62 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO56 |
| TAS5112DFD | 62 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO56 |
| TAS5112DFDR | 62 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO56 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TAS5112ADCAG4 | 功能描述:音频放大器 Digital Amp Power Stage RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TAS5112ADCAR | 功能描述:音频放大器 Digital Amp Power Stage RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TAS5112ADCARG4 | 功能描述:音频放大器 Digital Amp Power Stage RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TAS5112ADFD | 功能描述:音频放大器 Digital Amp Power Stage RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TAS5112ADFDG4 | 功能描述:音频放大器 Digital Amp Power Stage RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。