- 您现在的位置：买卖IC网 > PDF目录98163 > TAS5414ATPHDMQ1G4 (TEXAS INSTRUMENTS INC) 116 W, 4 CHANNEL, AUDIO AMPLIFIER, PQFP64 PDF资料下载
参数资料
| 型号： | TAS5414ATPHDMQ1G4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 116 W, 4 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| 封装： | GREEN, PLASTIC, HTQFP-64 |
| 文件页数： | 21/54页 |
| 文件大小： | 1386K |
| 代理商： | TAS5414ATPHDMQ1G4 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页
SLOS535C
– MAY 2009 – REVISED APRIL 2011
Table 18. External Control Register 6 (0x0D) Output Control
D7
D6
D5
D4
D3
D2
D1
D0
FUNCTION
0
Low-low state disabled all channels
–
1
Set channel 1 to low-low state
–
1
–
Set channel 2 to low-low state
–
1
–
Set channel 3 to low-low state
–
1
–
Set channel 4 to low-low state
X
–
Reserved
Table 19. External Control Register 7 (0x0E) Positive DC Detect Threshold Selection
D7
D6
D5
D4
D3
D2
D1
D0
FUNCTION
1
0
1
0
Default positive dc detect value
0
1
0
1
0
1
Minimum positive dc detect value
X
See Figure 11 to set positive dc detect value
1
0
1
0
1
Maximum positive dc detect value
Table 20. External Control Register 8 (0x0F) Negative DC Detect Threshold Selection
D7
D6
D5
D4
D3
D2
D1
D0
FUNCTION
0
1
0
1
Default negative dc detect value
0
1
0
1
0
1
Minimum negative dc detect value
X
See Figure 12 to set negative dc detect value
0
Maximum negative dc detect value
Hardware Control Pins
The TAS5414A and TAS5424A incorporate four discrete hardware pins for real-time control and indication of
device status.
FAULT pin: This active-low, open-drain output pin indicates the presence of a fault condition that requires the
TAS5414A and TAS5424A to go automatically into the Hi-Z mode or standby mode. When this pin is
asserted high, the device has acted to protect itself and the system from potential damage. The exact nature
of the fault can be read via I2C with the exception of faults that are the result of PVDD voltage excursions
above 25 Vdc or below 6 Vdc. In these instances, the device goes into standby mode and the I2C bus is no
longer operational. However, the fault is still indicated due to the fact that the FAULT pin is open-drain and
active-high.
CLIP_OTW pin: The function of this active-low pin is configured by the user to indicate one of the following
conditions: overtemperature warning, the detection of clipping, or the logical OR of both of these conditions.
The configuration is selected via I2C. During tweeter detect diagnostics, this pin also is asserted when a
tweeter is present.
MUTE pin: This active-low pin is used for hardware control of the mute/unmute function for all four channels.
Capacitor CMUTE is used to control the time constant for the gain ramp needed to produce a pop- and
click-free mute function. For pop- and click-free operation, the mute function should be implemented through
I2C commands. The use of a hard mute with an external transistor does not ensure pop- and click-free
operation, and is not recommended unless an emergency hard mute function is required in case of a loss of
I2C control. For proper pop- and click-free operation the minimum recommended value of CMUTE is 330 nF.
STANDBY pin: When this active-low pin is asserted, the device goes into a complete shutdown, and current
draw is limited to 2
μA, typical. This is pin typically asserted when the car ignition is in the off position. It can
also be used to shut down the device rapidly when certain operating conditions are violated. All I2C register
content is lost when this pin is asserted. The I2C bus goes into the high-impedance state when the
STANDBY pin is asserted.
28
Copyright
2009–2011, Texas Instruments Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| TAS5414ATPHDQ1G4 | 116 W, 4 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| TAS5414ATPHDRMQ1G4 | 116 W, 4 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| TAS5414ATPHDRQ1G4 | 116 W, 4 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| TAS5424ATPHDMQ1 | 116 W, 4 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| TAS5424ATPHDQ1 | 116 W, 4 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TAS5414ATPHDQ1 | 功能描述:音频放大器 4Ch Auto Dig Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TAS5414ATPHDQ1G4 | 功能描述:音频放大器 4 Channel Auto Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TAS5414ATPHDRMQ1 | 功能描述:音频放大器 4Ch Auto Dig Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TAS5414ATPHDRMQ1G4 | 功能描述:音频放大器 4 Channel Auto Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TAS5414ATPHDRQ1 | 功能描述:音频放大器 4Ch Auto Dig Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。