- 您现在的位置：买卖IC网 > PDF目录98164 > TAS5601DCARG4 (TEXAS INSTRUMENTS INC) 20 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO56 PDF资料下载
参数资料
| 型号： | TAS5601DCARG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 20 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO56 |
| 封装： | GREEN, PLASTIC, HTSSOP-56 |
| 文件页数： | 7/26页 |
| 文件大小： | 2698K |
| 代理商： | TAS5601DCARG4 |
BSN and BSP Capacitors
VCLAMP Capacitor
VBYP Capacitor Selection
RESET OPERATION
USING LOW-ESR CAPACITORS
www.ti.com....................................................................................................................................... SLAS585A – FEBRUARY 2008 – REVISED SEPTEMBER 2008
ensure that the output total harmonic distortion (THD) is as low as possible. Power-supply decoupling also
prevents oscillations for long lead lengths between the amplifier and the speaker. The optimum decoupling is
achieved by using two capacitors of different types that target different types of noise on the power-supply leads.
For higher-frequency transients, spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR)
ceramic capacitor, typically 0.1
F to 1 F, placed as close as possible to the device V
CC lead works best. For
filtering lower frequency noise signals, a larger aluminum electrolytic capacitor of 220
F or greater placed near
the audio power amplifier is recommended. The 220-
F capacitor also serves as local storage capacitor for
supplying current during large signal transients on the amplifier outputs. The PVCC terminals provide the power
to the output transistors, so a 220-
F or larger capacitor should be placed on each PVCC terminal. A 10-F
capacitor on the AVCC terminal is adequate. These capacitors must be properly derated for voltage and
ripple-current rating to ensure reliability.
The half H-bridge output stages use only NMOS transistors. Therefore, they require bootstrap capacitors for the
high side of each output to turn on correctly. A 220-nF ceramic capacitor, rated for at least 25 V, must be
connected from each output to its corresponding bootstrap input.
The bootstrap capacitors connected between the BSx pins and their corresponding outputs function as a floating
power supply for the high-side N-channel power MOSFET gate-drive circuitry. During each high-side switching
cycle, the bootstrap capacitors hold the gate-to-source voltage high enough to keep the high-side MOSFETs
turned on.
To ensure that the maximum gate-to-source voltage for the NMOS output transistors is not exceeded, one
internal regulator clamps the gate voltage. One 1-
F capacitor must be connected from each VCLAMP (terminal)
to ground and must be rated for at least 16 V. The voltages at the VCLAMP terminal may vary with VCC and may
not be used for powering any other circuitry.
The scaled supply reference (BYPASS) nominally provides an AVCC/8 internal bias for the preamplifier stages.
The external capacitor for this reference (CBYP) is a critical component and serves several important functions.
During start-up or recovery from shutdown mode, CBYP determines the rate at which the amplifier starts. The start
up time is proportional to 0.5 s per microfarad in single-ended mode (SE/BTL = DVDD). Thus, the recommended
1-
F capacitor results in a start-up time of approximately 500 ms (SE/BTL = DVDD). The second function is to
reduce noise produced by the power supply caused by coupling with the output drive signal. This noise could
result in degraded power-supply rejection and THD+N.
The circuit is designed for a CBYP value of 1 F for best pop performance. The input capacitors should have the
same value. A ceramic or tantalum low-ESR capacitor is recommended.
The TAS5601 employs a RESET mode of operation designed to reduce supply current (ICC) to the absolute
minimum level during periods of nonuse for power conservation. The RESET input terminal should be held high
(see specification table for trip point) during normal operation when the amplifier is in use. Pulling RESET low
causes the outputs to amp to GND and the amplifier to enter a low-current state. Never leave RESET
unconnected, because amplifier operation would be unpredictable.
For the best power-up pop performance, place the amplifier in the RESET mode prior to applying the
power-supply voltage.
Low-ESR capacitors are recommended throughout this application section. A real (as opposed to ideal) capacitor
can be modeled simply as a resistor in series with an ideal capacitor. The voltage drop across this resistor
minimizes the beneficial effects of the capacitor in the circuit. The lower the equivalent value of this resistance,
the more the real capacitor behaves like an ideal capacitor.
Copyright 2008, Texas Instruments Incorporated
15
Product Folder Link(s): TAS5601
相关PDF资料 |
PDF描述 |
|---|---|
| TAS5601DCAR | 20 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO56 |
| TAS5601DCA | 20 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO56 |
| TAS5611DKD | 125 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO44 |
| TAS5611PHD | 125 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| TAS5611PHDR | 125 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TAS5601EVM4 | 功能描述:音频 IC 开发工具 TAS5601EVM4 Eval Mod RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| TAS5602 | 制造商:TI 制造商全称:Texas Instruments 功能描述:20W STEREO DIGITAL AMPLIFIER POWER STAGE |
| TAS5602_1 | 制造商:TI 制造商全称:Texas Instruments 功能描述:20W STEREO DIGITAL AMPLIFIER POWER STAGE |
| TAS5602DCA | 功能描述:音频放大器 20W Stereo Dig Amp Pwr Stage RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TAS5602DCAG4 | 功能描述:音频放大器 20W Stereo Dig Amp Pwr Stage w/ FB RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。