- 您现在的位置：买卖IC网 > PDF目录98164 > TAS5613APHDR (TEXAS INSTRUMENTS INC) 150 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 PDF资料下载
参数资料
| 型号： | TAS5613APHDR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 150 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| 封装： | GREEN, PLASTIC, HTQFP-64 |
| 文件页数： | 9/28页 |
| 文件大小： | 1505K |
| 代理商： | TAS5613APHDR |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
SLAS711A
– JUNE 2010 – REVISED MARCH 2011
THEORY OF OPERATION
POWER SUPPLIES
To facilitate system design, the TAS5613A needs only a 12V supply in addition to the (typical) 36V power-stage
supply. An internal voltage regulator provides suitable voltage levels for the digital and low-voltage analog
circuitry. Additionally, all circuitry requiring a floating voltage supply, e.g., the high-side gate drive, is
accommodated by built-in bootstrap circuitry requiring only an external capacitor for each half-bridge.
In order to provide outstanding electrical and acoustical characteristics, the PWM signal path including gate drive
and output stage is designed as identical, independent half-bridges. For this reason, each half-bridge has
separate gate drive supply (GVDD_X), bootstrap pins (BST_X), and power-stage supply pins (PVDD_X).
Furthermore, an additional pin (VDD) is provided as supply for all common circuits. Although supplied from the
same 12V source, separating to GVDD_A, GVDD_B, GVDD_C, GVDD_D, and VDD on the printed-circuit board
(PCB) by RC filters (see application diagram for details) is recommended. These RC filters provide the
recommended high-frequency isolation. Special attention should be paid to placing all decoupling capacitors as
close to their associated pins as possible. In general, inductance between the power supply pins and decoupling
capacitors must be avoided. (See reference board documentation for additional information.)
For a properly functioning bootstrap circuit, a small ceramic capacitor must be connected from each bootstrap pin
(BST_X) to the power-stage output pin (OUT_X). When the power-stage output is low, the bootstrap capacitor is
charged through an internal diode connected between the gate-drive power-supply pin (GVDD_X) and the
bootstrap pin. When the power-stage output is high, the bootstrap capacitor potential is shifted above the output
potential and thus provides a suitable voltage supply for the high-side gate driver. In an application with PWM
switching frequencies in the range from 300kHz to 400kHz, it is recommended to use 33nF ceramic capacitors,
size 0603 or 0805, for the bootstrap supply. These 33nF capacitors ensure sufficient energy storage, even during
minimal PWM duty cycles, to keep the high-side power stage FET (LDMOS) fully turned on during the remaining
part of the PWM cycle.
Special attention should be paid to the power-stage power supply; this includes component selection, PCB
placement, and routing. As indicated, each half-bridge has independent power-stage supply pins (PVDD_X). For
optimal electrical performance, EMI compliance, and system reliability, it is important that each PVDD_X pin is
decoupled with a 2-
μF ceramic capacitor placed as close as possible to each supply pin. It is recommended to
follow the PCB layout of the TAS5613A reference design. For additional information on recommended power
supply and required components, see the application diagrams in this data sheet.
The 12V supply should be from a low-noise, low-output-impedance voltage regulator. Likewise, the 36V
power-stage supply is assumed to have low output impedance and low noise. The power-supply sequence is not
critical as facilitated by the internal power-on-reset circuit. Moreover, the TAS5613A is fully protected against
erroneous power-stage turn on due to parasitic gate charging. Thus, voltage-supply ramp rates (dV/dt) are
non-critical within the specified range (see the Recommended Operating Conditions table of this data sheet).
SYSTEM POWER-UP/POWER-DOWN SEQUENCE
Powering Up
The TAS5613A does not require a power-up sequence. The outputs of the H-bridges remain in a
high-impedance state until the gate-drive supply voltage (GVDD_X) and VDD voltage are above the undervoltage
protection (UVP) voltage threshold (see the Electrical Characteristics table of this data sheet). Although not
specifically required, it is recommended to hold RESET in a low state while powering up the device. This allows
an internal circuit to charge the external bootstrap capacitors by enabling a weak pulldown of the half-bridge
output.
Powering Down
The TAS5613A does not require a power-down sequence. The device remains fully operational as long as the
gate-drive supply (GVDD_X) voltage and VDD voltage are above the undervoltage protection (UVP) voltage
threshold (see the Electrical Characteristics table of this data sheet). Although not specifically required, it is a
good practice to hold RESET low during power down, thus preventing audible artifacts including pops or clicks.
Copyright
2010–2011, Texas Instruments Incorporated
17
Product Folder Link(s): TAS5613A
相关PDF资料 |
PDF描述 |
|---|---|
| TAS5613APHD | 150 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| TAS5614ADKDR | 150 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO44 |
| TAS5614ADKD | 150 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO44 |
| TAS5614APHDR | 150 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| TAS5614APHD | 150 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TAS5613DKD | 制造商:TI 制造商全称:Texas Instruments 功能描述:150W STEREO / 300W MONO PurePath? HD ANALOG-INPUT POWER STAGE |
| TAS5613DKDR | 制造商:Texas Instruments 功能描述: |
| TAS5613PHD | 功能描述:音频放大器 150W Stereo PurePath HD Ana-In Pwr Stage RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TAS5613PHD | 制造商:Texas Instruments 功能描述:Speaker Amplifier IC |
| TAS5613PHD2EVM | 功能描述:音频 IC 开发工具 TAS5613PHD Eval Mod RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
发布紧急采购，3分钟左右您将得到回复。