- 您现在的位置：买卖IC网 > PDF目录98164 > TAS5615DKD (TEXAS INSTRUMENTS INC) 300 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO44 PDF资料下载
参数资料
| 型号： | TAS5615DKD |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 300 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO44 |
| 封装： | PLASTIC, HSSOP-44 |
| 文件页数： | 16/35页 |
| 文件大小： | 1790K |
| 代理商： | TAS5615DKD |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
www.ti.com
SLAS595B – JUNE 2009 – REVISED FEBRUARY 2010
output LC filter. The typical duration is < 15 ms/mF. While the PPSC detection is in progress, SD is kept low, and
the device does not react to changes applied to the RESET pin. If no shorts are present, the PPSC detection
passes, and SD is released. A device reset does not start a new PPSC detection. PPSC detection is enabled in
BTL and PBTL output configurations; the detection is not performed in SE mode. To make sure not to trip the
PPSC detection system, it is recommended not to insert resistive load to GND_X or PVDD_X.
OVERTEMPERATURE PROTECTION
The two different package options have individual overtemperature protection schemes.
PHD Package
The TAS5615 PHD package option has a three-level temperature-protection system that asserts an active-low
warning signal (OTW1) when the device junction temperature exceeds 100°C (typical), (OTW2) when the device
junction temperature exceeds 125°C (typical) and, if the device junction temperature exceeds 155°C (typical), the
device is put into thermal shutdown, resulting in all half-bridge outputs being set in the high-impedance (Hi-Z)
state and SD being asserted low. OTE is latched in this case. To clear the OTE latch, RESET must be asserted.
Thereafter, the device resumes normal operation.
DKD Package
The TAS5615 DKD package option has a two-level temperature-protection system that asserts an active-low
warning signal (OTW) when the device junction temperature exceeds 125°C (typical) and, if the device junction
temperature exceeds 155°C (typical), the device is put into thermal shutdown, resulting in all half-bridge outputs
being set in the high-impedance (Hi-Z) state and SD being asserted low. OTE is latched in this case. To clear the
OTE latch, RESET must be asserted. Thereafter, the device resumes normal operation.
UNDERVOLTAGE PROTECTION (UVP) AND POWER-ON RESET (POR)
The UVP and POR circuits of the TAS5615 fully protect the device in any power-up/down and brownout situation.
While powering up, the POR circuit resets the overload circuit (OLP) and ensures that all circuits are fully
operational when the GVDD_X and VDD supply voltages reach levels stated in the Electrical Characteristics
table. Although GVDD_X and VDD are independently monitored, a supply-voltage drop below the UVP threshold
on any VDD or GVDD_X pin results in all half-bridge outputs immediately being set in the high-impedance (Hi-Z)
state and SD being asserted low. The device automatically resumes operation when all supply voltages have
increased above the UVP threshold.
DEVICE RESET
When RESET is asserted low, all power-stage FETs in the four half-bridges are forced into a high-impedance
(Hi-Z) state.
In BTL modes, to accommodate bootstrap charging prior to switching start, asserting the reset input low enables
weak pulldown of the half-bridge outputs. In the SE mode, the output is forced into a high-impedance state when
asserting the reset input low.
Asserting the reset input low removes any fault information to be signalled on the SD output, i.e., SD is forced
high. A rising-edge transition on reset input allows the device to resume operation after an overload fault. To
ensure thermal reliability, the rising edge of reset must occur no sooner than 4 ms after the falling edge of SD.
SYSTEM DESIGN CONSIDERATION
A rising-edge transition on the reset input allows the device to execute the start-up sequence and starts
switching.
Apply only audio when the state of READY is high; that starts and stops the amplifier without having audible
artifacts in the output transducers. If an overcurrent protection event is introduced, the READY signal goes low;
hence, filtering is needed if the signal is intended for audio muting in non-microcontroller systems.
The CLIP signal indicates that the output is approaching clipping. The signal can be used to decrease either an
audio volume or an intelligent power supply controlling a low and a high rail.
The device inverts the audio signal from input to output.
Copyright 2009–2010, Texas Instruments Incorporated
23
Product Folder Link(s) :TAS5615
相关PDF资料 |
PDF描述 |
|---|---|
| TAS5615PHD | 300 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| TAS5630PHDR | 300 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| TAS5630DKDR | 600 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO44 |
| TAS5630DKD | 600 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO44 |
| TAS5630PHD | 600 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TAS5615DKD2EVM | 功能描述:音频 IC 开发工具 TAS5615DKD2 Eval Mod RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| TAS5615DKDR | 功能描述:音频放大器 Ana inp 150W Stereo class D Amplifier RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TAS5615PHD | 功能描述:音频放大器 Analog input 160W RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TAS5615PHD2EVM | 功能描述:音频 IC 开发工具 TAS5615PHD Eval Mod RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| TAS5615PHDR | 功能描述:音频放大器 Analog input 160W RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。