- 您现在的位置：买卖IC网 > PDF目录98165 > TAS5706PAP (TEXAS INSTRUMENTS INC) 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 PDF资料下载
参数资料
| 型号： | TAS5706PAP |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| 封装： | 10 X 10 MM, GREEN, PLASTIC, HTQFP-64 |
| 文件页数： | 51/70页 |
| 文件大小： | 1169K |
| 代理商： | TAS5706PAP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页当前第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页
www.ti.com
SLOS550B – DECEMBER 2007 – REVISED DECEMBER 2010
OSCILLATOR TRIM REGISTER (0x1B)
The TAS5706 PWM processor contains an internal oscillator for PLL reference. This reduces system cost
because an external reference is not required. Currently, TI recommends a trim resistor value of 18.2 k
(1%).
This should be connected between OSC_RES and DVSS.
The factory-trim procedure simply enables the factory trim that was previously done at the factory.
Note that trim always must be run following reset of the device.
Oscillator Trim Enable Procedure Example
Write data 0x00 to register 0x1B (enable factory trim).
Table 18. Oscillator Trim Register (0x1B)
D7
D6
D5
D4
D3
D2
D1
D0
FUNCTION
1
–
Reserved (1)
–
0
–
Oscillator trim not done (read-only) (1)
–
1
–
Oscillator trim done (read only)
–
0
–
Reserved (1)
–
0
–
Select factory trim (Write a 0 to select factory trim; default is 1.)
–
1
–
Factory trim disabled (1)
–
0
Reserved (1)
(1)
Default values are in bold.
BKND_ERR REGISTER (0x1C)
When a back-end error signal is received (BKND_ERR = LOW), all the output stages are reset by setting all
PWM, VALID1, and VALID2 signals LOW. Subsequently, the modulator waits approximately for the time listed in
Table 19 before initiation of a reset.
Table 19. BKND_ERR Register (0x1C)
D7
D6
D5
D4
D3
D2
D1
D0
FUNCTION
–
0
Set back-end reset period to 0 ms (Reserved)
–
0
1
Set back-end reset period to 150 ms (Reserved)
–
0
1
0
Set back-end reset period to 299 ms (1)
–
0
1
Set back-end reset period to 449 ms
–
0
1
0
Set back-end reset period to 598 ms
–
0
1
0
1
Set back-end reset period to 748 ms
–
0
1
0
Set back-end reset period to 898 ms
–
0
1
Set back-end reset period to 1047 ms
–
1
0
Set back-end reset period to 1197 ms
–
1
0
1
Set back-end reset period to 1346 ms
–
1
0
1
0
Set back-end reset period to 1496 ms
–
1
0
1
Set back-end reset period to 1496 ms
–
1
–
Set back-end reset period to 1496 ms
(1)
Default values are in bold.
Copyright 2007–2010, Texas Instruments Incorporated
55
Product Folder Link(s): TAS5706
相关PDF资料 |
PDF描述 |
|---|---|
| TAS5706PAPG4 | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| TAS5707APHPR | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
| TAS5707APHP | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
| TAS5707PHPR | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
| TAS5707PHP | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TAS5706PAPG4 | 功能描述:音频放大器 20W stereo Dig Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TAS5706PAPR | 功能描述:音频放大器 20W stereo Dig Audio Pwr Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TAS5706PAPRG4 | 功能描述:音频放大器 20W stereo Dig Audio Pwr Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TAS5707 | 制造商:TI 制造商全称:Texas Instruments 功能描述:20-W STEREO DIGITAL AUDIO POWER AMPLIFIER WITH EQ AND DRC |
| TAS5707_13 | 制造商:TI 制造商全称:Texas Instruments 功能描述:20-W STEREO DIGITAL AUDIO POWER AMPLIFIER WITH EQ AND DRC |
发布紧急采购，3分钟左右您将得到回复。