- 您现在的位置：买卖IC网 > PDF目录225279 > TB62205F STEPPER MOTOR CONTROLLER, 0.96 A, PDSO36 PDF资料下载
参数资料
| 型号： | TB62205F |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 0.96 A, PDSO36 |
| 封装： | 0.450 INCH, 0.65 MM PITCH, PLASTIC, HSOP-36 |
| 文件页数： | 21/36页 |
| 文件大小： | 826K |
| 代理商： | TB62205F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
TB62205F
2005-04-04
28
Operating Time of Overcurrent Protection Circuit
ISD non-detection time and ISD operating time
The overcurrent protection circuit has a non-detection time to prevent erroneous detection of spike current
generated in diode recovery current (IRR) or at switching. The non-detection time being synchronized with
the CR cycle for setting chopping frequency is expressed as follows.
Non-detection time = 4 × CR cycle
Time required to stop the output after overcurrent flows into the output stage is expressed as follows.
Minimum time = 5 × CR cycle
Maximum time = 8 × CR cycle
Note that the operating times as shown above are achieved when overcurrent flows as it is expected.
Depends on the timing of output control mode, the circuit may not be triggered.
Thus, to ensure safe operation, please insert a fuse in the VM power supply.
(The capacity of the fuse is determined according to a condition to be used. Please select one whose capacity
does not exceed the power dissipation for the IC to avoid any operating problems.)
min
Output stops (RESET mode)
CR oscillating
(chopping reference waveform)
max
min
ISD operating time
(Non-detection time)
ISD BLANK time
When overcurrent starts to flow into the output stage
(overcurrent state occurs)
相关PDF资料 |
PDF描述 |
|---|---|
| TB6608FNG | STEPPER MOTOR CONTROLLER, 0.8 A, PDSO20 |
| TBS22A | SINGLE COLOR LED |
| TBT4854 | Pigtailed PD for analog application |
| TBT4855 | Pigtailed PD for analog application |
| TBT4856 | Pigtailed PD for analog application |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TB62206FG | 制造商:Toshiba America Electronic Components 功能描述:2-Phase Stepping Motor Driver 5V 22-Pin(20+2Tab) HSOP |
| TB62206FG(EL) | 功能描述:马达/运动/点火控制器和驱动器 Stepping Motor Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB62206FG(O,EL) | 功能描述:马达/运动/点火控制器和驱动器 2-Phase Bipolar IC 40V 1.8A POR RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB62207BFG(O,EL) | 制造商:Toshiba America Electronic Components 功能描述:2 STEPPER MOTOR DRIVE, 40V 1.5A HSOP36 制造商:Toshiba America Electronic Components 功能描述:2 Stepper Motor Drive 37V 2.5A TB62207BF |
| TB62207BFG(OEL) | 制造商:Toshiba America Electronic Components 功能描述:2 STEPPER MOTOR DRIVE 40V 1.5A HSOP36 |
发布紧急采购，3分钟左右您将得到回复。