- 您现在的位置：买卖IC网 > PDF目录98166 > TB62214FTG STEPPER MOTOR CONTROLLER, 2 A, PQCC48 PDF资料下载
参数资料
| 型号： | TB62214FTG |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 2 A, PQCC48 |
| 封装： | 7 X 7 MM, 0.50 MM PITCH, ROHS COMPLIANT, PLASTIC, QFN-48 |
| 文件页数： | 3/27页 |
| 文件大小： | 687K |
| 代理商： | TB62214FTG |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
TB62214FG/FTG
2010-06-10
11
Electrical Characteristics 2 (Ta = 25°C, VM = 24 V, unless otherwise specified)
Characteristics
Symbol
Test
Circuit
Test Condition
Min
Typ.
Max
Unit
Vref input current
Iref
DC
Vref = 3.0 V
0
1
μA
Vref decay rate
Vref (GAIN)
DC
Vref = 2.0 V
1/4.8
1/5.0
1/5.2
TSD threshold
(Note 1)
TjTSD
DC
140
150
170
°C
VM recovery voltage
VMR
DC
7.0
8.0
9.0
V
Overcurrent trip threshold
(Note 2)
ISD
DC
2.0
3.0
4.0
A
Supply voltage for internal circuitry
VCC
DC
ICC = 5.0 mA
4.75
5.00
5.25
V
Note 1: Thermal shutdown (TSD) circuitry
When the junction temperature of the device has reached the threshold, the TSD circuitry is tripped, causing
the internal reset circuitry to turn off the output transistors.
The TSD circuitry is tripped at a temperature between 140°C (min) and 170°C (max). Once tripped, the TSD
circuitry keeps the output transistors off until both the D_MODE_1 and D_MODE_2 pins are switched to Low
or the TB62214FG/FTG is rebooted.
The thermal shutdown circuit is provided to turn off all the outputs when the IC is overheated. For this
reason, please avoid using TSD for other purposes.
Note 2: Overcurrent shutdown (ISD) circuitry
When the output current has reached the threshold, the ISD circuitry is tripped, causing the internal reset
circuitry to turn off the output transistors.
To prevent the ISD circuitry from being tripped due to switching noise, it has a masking time of four CR
oscillator cycles. Once tripped, it takes a maximum of four cycles to exit ISD mode and resume normal
operation.
The ISD circuitry remains active until both the D_MODE_1 and D_MODE_2 pins are switched to Low or the
TB62214FG/FTG is rebooted.
The TB62214FG/FTG remains in Standby mode while in ISD mode.
Note 3: If the supply voltage for internal circuitry (VCC) is split with an external resistor and used as Vref input supply
voltage, the accuracy of the output current setting will be at
±8% when the VCC output voltage accuracy and
the Vref damping ratio accuracy are combined.
Note 4: The circuit design has been designed so that electromotive force or leak current from signal input does not
occur when VM voltage is not supplied, even if the logic input signal is input. Even so, regulate logic input
signals before resupply of VM voltage so that the motor does not operate when voltage is reapplied.
Back-EMF
While a motor is rotating, there is a timing at which power is fed back to the power supply. At that timing, the
motor current recirculates back to the power supply due to the effect of the motor back-EMF.
If the power supply does not have enough sink capability, the power supply and output pins of the device might
rise above the rated voltages. The magnitude of the motor back-EMF varies with usage conditions and motor
characteristics. It must be fully verified that there is no risk that the TB62214FG/FTG or other components will be
damaged or fail due to the motor back-EMF.
Cautions on Overcurrent Shutdown (ISD) and Thermal Shutdown (TSD)
The ISD and TSD circuits are only intended to provide temporary protection against irregular conditions such as an
output short-circuit; they do not necessarily guarantee the complete IC safety.
If the device is used beyond the specified operating ranges, these circuits may not operate properly: then the device
may be damaged due to an output short-circuit.
The ISD circuit is only intended to provide a temporary protection against an output short-circuit. If such a
condition persists for a long time, the device may be damaged due to overstress. Overcurrent conditions must be
removed immediately by external hardware.
IC Mounting
Do not insert devices incorrectly or in the wrong orientation. Otherwise, it may cause breakdown, damage and/or
deterioration of the device.
相关PDF资料 |
PDF描述 |
|---|---|
| TB62754AFNG | SWITCHING REGULATOR, PDSO20 |
| TB62756FUG | SWITCHING REGULATOR, 1430 kHz SWITCHING FREQ-MAX, PDSO6 |
| TB62757FUG | SWITCHING REGULATOR, 1430 kHz SWITCHING FREQ-MAX, PDSO6 |
| TB6512AFG | STEPPER MOTOR CONTROLLER, 0.12 A, PDSO24 |
| TB6513AF | BRUSHLESS DC MOTOR CONTROLLER, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TB62215AFG(O,8,EL) | 功能描述:马达/运动/点火控制器和驱动器 PWM Method Clock BiCD 40V 3.0A RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB62215AFNG(OC8,EL | 功能描述:马达/运动/点火控制器和驱动器 PWM Method Clock BiCD 40V 3.0A RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB62215AFTG(O,8,EL | 功能描述:马达/运动/点火控制器和驱动器 PWM Method Clock BiCD 40V 3.0A RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB62215AHQ(O) | 功能描述:马达/运动/点火控制器和驱动器 PWM Method Clock BiCD 40V 3.0A RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB62215SM1 | 制造商:THOMAS & BETTS 功能描述: |
发布紧急采购，3分钟左右您将得到回复。