- 您现在的位置：买卖IC网 > PDF目录98167 > TB6549HQ BRUSH DC MOTOR CONTROLLER, 5 A, ZIP25 PDF资料下载
参数资料
| 型号： | TB6549HQ |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSH DC MOTOR CONTROLLER, 5 A, ZIP25 |
| 封装： | 1MM PITCH, HZIP-25 |
| 文件页数： | 2/22页 |
| 文件大小： | 377K |
| 代理商： | TB6549HQ |
TB6549FG/PG/HQ
2010-07-13
10
6. VCC Power Supply Section
The VCC power supply delivers a voltage to the output circuit, charge pump circuit, and internal 5 V
circuit.
The operating voltage range is shown below:
VCC (opr.) = 10 to 27 V
This IC has a power monitoring function for preventing an output malfunction on power-up. However,
Toshiba recommends that IN1, IN2, and SB be set to the Low level at power-on.
7. GND Sections
This IC includes two separate GND sections: S-GND for controlling and P-GND for outputting. Be sure
to short-circuit these two GNDs as close to TB6549 as possible.
8. Power Monitoring Circuit
This circuit turns the output OFF when Vreg becomes 3.0 V (design target value) or less. At this time,
VCC = 4.6 V (typ.).
With a hysteresis of 0.3 V (design target value), the output turns back ON when Vreg exceeds 3.3 V
(design target value) after this circuit starts operating.
9. Thermal Shutdown (TSD) Circuit
This IC includes a thermal shutdown circuit, which turns the output OFF when the junction temperature
(Tj) exceeds 160°C (typ.). The output turns back ON automatically. The thermal hysteresis is 20°C.
TSD = 160°C (design target value)
ΔTSD = 20°C (design target value)
10. Overcurrent Detection (ISD) Circuit
This IC includes a circuit to detect current flowing through the output power transistors. The current limit
is set to 5 A (typ.). The circuit detects a current flowing through each of the four output power transistors.
If the current in any one output power transistor exceeds the set limit, this circuit turns all the outputs
OFF.
This circuit includes a timer that causes the outputs to be OFF for 50
μs (typ.) after detection of an
overcurrent and then turn back ON automatically. If the overcurrent continues to flow, this ON-OFF
operation is repeated. Note that to prevent a malfunction due to a glitch, an insensitive period of 10
μs
(typ.) is provided.
The set limit is 5 A (typ.) as a design target value. The distributions shown below exist because of the
variations in thermal characteristics of different ICs. These distributions should be fully considered in the
motor torque design.
Also, output peak current should be less than 3 A because of the variations below,
Detected current: Approximately from 3.5 to 6.5 A
ILIM
50
μs
(typ.)
0
10
μs
(typ.)
Insensitive period
50
μs
(typ.)
10
μs
(typ.)
Output Current
相关PDF资料 |
PDF描述 |
|---|---|
| TB6551FAG | BRUSHLESS DC MOTOR CONTROLLER, PDSO24 |
| TB6552FL | BRUSH DC MOTOR CONTROLLER, 1 A, PQCC24 |
| TB6552FN | BRUSH DC MOTOR CONTROLLER, 1 A, PDSO16 |
| TB6559FG | BRUSH DC MOTOR CONTROLLER, 2.5 A, PDSO16 |
| TB6560AFG | STEPPER MOTOR CONTROLLER, 2.5 A, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TB6549HQ(O) | 功能描述:马达/运动/点火控制器和驱动器 30V Bridge DRVR 3.5A 1.0 Ohm low RDS RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB6549P | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:Full-Bridge Driver IC for DC Motors |
| TB6549PG | 功能描述:马达/运动/点火控制器和驱动器 Bridge Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB6549PG(O) | 功能描述:马达/运动/点火控制器和驱动器 30V PWR Supply 3.5A Full Bridge DRVR PWM RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB6551F | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:3-Phase Full-Wave Sine-Wave PWM Brushless Motor Controller |
发布紧急采购，3分钟左右您将得到回复。