- 您现在的位置：买卖IC网 > PDF目录69402 > TB6556F BRUSHLESS DC MOTOR CONTROLLER, PDSO30 PDF资料下载
参数资料
| 型号： | TB6556F |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, PDSO30 |
| 封装： | 0.375 INCH, 1 MM PITCH, PLASTIC, SSOP-30 |
| 文件页数： | 7/22页 |
| 文件大小： | 520K |
| 代理商： | TB6556F |
TB6556F/FG
2006-03-02
15
The modulation waveform is generated using Hall signals. The modulation waveform is then compared
with the triangular wave and a sine-wave PWM signal is generated.
The time (electrical degrees: 60°) from the rising (or falling) edges of the three Hall signals to the next
falling (or rising) edges is counted. The counted time is used as the data for the next 60° phase of the
modulation waveform.
There are 32 items of data for the 60° phase of the modulation waveform. The time width of one data
item is 1/32 of the time width of the 60° phase of the previous modulation waveform. The modulation
waveform moves forward by the width.
In the above diagram, the modulation waveform (1)’ data moves forward by the 1/32 time width of the
time (1) from HU:
↑ to HW: ↓. Similarly, data (2)’ moves forward by the 1/32 time width of the time (2) from
HW:
↓ to HV: ↑.
If the next edge does not occur after the 32 data items end, the next 32 data items move forward by the
same time width until the next edge occurs.
The modulation wave is brought into phase with every zero-cross point of the Hall signal.
The modulation wave is reset in synchronization with the rising and falling edges of the Hall signal at
every 60° electrical angle. Thus, when the Hall device is not placed at the correct position or during
acceleration and deceleration, the modulation waveform is not continuous at every reset.
*t
SV
(1)’
1
2
3
4
5
6
30
31
32
32 data items
*t
* t
= t(1) × 1/32
HU
HV
HW
SU
SV
Sw
⑤
②
⑥
①
③
⑥’
①’
②’
③’
*HU, HV, HW: Hall signals
相关PDF资料 |
PDF描述 |
|---|---|
| TB6557FLG | BRUSH DC MOTOR CONTROLLER, QCC36 |
| TB6562ANG | STEPPER MOTOR CONTROLLER, 1.5 A, PDIP24 |
| TB6572AFG | BRUSHLESS DC MOTOR CONTROLLER, 0.025 A, PQFP52 |
| TB6592FLG | BRUSH DC MOTOR CONTROLLER, 0.8 A, PQCC24 |
| TB6818FG | POWER FACTOR CONTROLLER, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TB6556FG | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:3-Phase Full-Wave Sine-Wave PWM Brushless Motor Controller |
| TB6556FG(EL,DRY) | 功能描述:马达/运动/点火控制器和驱动器 BRUSHLESS DC MOTOR CONTROLLER 3-PHASE RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB6556FG(O,EL,DRY) | 功能描述:马达/运动/点火控制器和驱动器 3-Phase Full-Wave 12V Vcc=6V to 10V RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB6556FG(O8,EL,DRY | 功能描述:马达/运动/点火控制器和驱动器 3-phase PWM 252Hz 5V 30mA 6V to 10V RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB6556FGELDRY | 功能描述:马达/运动/点火控制器和驱动器 Brushless DC Motor Controller RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。