- 您现在的位置：买卖IC网 > PDF目录98167 > TB6581HG BRUSHLESS DC MOTOR CONTROLLER, 2 A, PZIP25 PDF资料下载
参数资料
| 型号： | TB6581HG |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 2 A, PZIP25 |
| 封装： | 1 MM PITCH, LEAD FREE, PLASTIC, HZIP-25 |
| 文件页数： | 13/15页 |
| 文件大小： | 583K |
| 代理商： | TB6581HG |
TB6581H/HG
2006-03-02
7
5.
Setting the carrier frequency
This function sets the triangular wave cycle (carrier cycle) necessary for generating the PWM signal.
(The triangular wave is used for forcibly turning on the lower transistor when the motor is driven by
square wave.)
Carrier cycle
= fosc/252 (Hz)
fosc = reference clock (crystal oscillation)
6.
Outputting the reverse rotation detection signal
This function detects the motor rotation direction every electrical angle of 360°. This function judges
whether the actual direction of a rotating motor coincides with that of the internal reference voltage.
Actual Motor Rotating Direction
REV Pin
Drive Mode
CW (forward)
HIGH
Square waveform (120° turn-on mode)
CCW (reverse)
LOW
Sine-wave waveform (180° turn-on mode)
*: CW or CCW of the motor is determined by the direction of the Hall signal, which is specified in the timing
chart on page 9.
*: When the REV pin is set to LOW, and the Hall signal is higher than 5 Hz, sine-wave drive mode is turned
on.
7.
Protecting input pin
(1)
Overcurrent protection (Pin Idc)
When the DC-link-current exceeds the internal reference voltage, gate block protection is performed.
Overcurrent protection is released for each carrier frequency.
Reference voltage
= 0.5 V (typ.)
(2)
Positional signal abnormality protection
Output is turned off when the positional signal is HHH or LLL; otherwise, it is restarted.
(3)
Monitor protection for VCC7/ VCC15 low supply voltage
For power supply on/off outside the operating voltage range, the U, V and W drive outputs are
turned off and the motor is stopped when there is a power supply fault.
< VCC7>
< VCC15>
Turn-off drive output
Turn-on drive output
Power supply voltage
4.5 V (typ.)
4.0 V (typ.)
GND
VB
VCC7
Output
Turn-off drive output
Turn-on drive output
Power supply voltage
11.5 V (typ.)
11.0 V (typ.)
GND
VB
VCC15
Turn-off drive output
Output
相关PDF资料 |
PDF描述 |
|---|---|
| TB6582FG | BRUSHLESS DC MOTOR CONTROLLER, 0.002 A, PQFP52 |
| TB6592FLG | BRUSH DC MOTOR CONTROLLER, 0.8 A, PQCC24 |
| TB6595FL | BRUSH DC MOTOR CONTROLLER, 0.8 A, PQCC36 |
| TB6598FN | STEPPER MOTOR CONTROLLER, 0.8 A, PDSO16 |
| TB6607FLG | STEPPER MOTOR CONTROLLER, 0.8 A, PQCC36 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TB6582FG | 功能描述:马达/运动/点火控制器和驱动器 Brushless DC Motor Controller RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB6582FG(ES) | 制造商:Toshiba America Electronic Components 功能描述: |
| TB6582FG(O,EL) | 功能描述:马达/运动/点火控制器和驱动器 Brushless DC Motor Controller RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB6582FG(OEL) | 制造商:Toshiba America Electronic Components 功能描述:BRUSHLESS DC MOTOR DRIVER 18V 0.2MA |
| TB6584AFNG(O,C8,EL | 功能描述:马达/运动/点火控制器和驱动器 Brushless Motor DRVR 3-Phase 1A 45V RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。