- 您现在的位置：买卖IC网 > PDF目录98167 > TB6582FG BRUSHLESS DC MOTOR CONTROLLER, 0.002 A, PQFP52 PDF资料下载
参数资料
| 型号： | TB6582FG |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 0.002 A, PQFP52 |
| 封装： | 10 X 10 MM, 0.65 MM PITCH, ROHS COMPLIANT, PLASTIC, QFP-52 |
| 文件页数： | 3/28页 |
| 文件大小： | 279K |
| 代理商： | TB6582FG |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
TB6582FG
2007-10-18
Design Specifications
11
(a)
DC excitation time
Duty cycle is determined by the gradient of SC terminal voltage, which depends on the charging of a
capacitor.
This voltage is clamped when the output duty cycle reaches about 35
% for the de-excitation and
over-current protection.
When CW
= U-phase → V-phase
When CCW
= U-phase → W-phase
Ta (typ.)
= 2.3 × CIP × RST (s)
(b)
Forced commutation time
The forced commutation is started when the IP pin voltage falls below to 0.5 V or lower.
The output duty cycle of forced commutation is determined by VSP input voltage.
FST = High
: Forced commutation frequency fST = fosc/(6 × 217)
FST = Middle
: Forced commutation frequency fST = fosc/(6 × 218)
FST = Low
: Forced commutation frequency fST = fosc/(6 × 219)
Example) When fOSC = 5 MHz,
FST = High
: fST 6.4 (Hz)
FST = Middle : fST 3.2 (Hz)
FST = Low or Open : fST 1.6 (Hz)
The rotor is aligned to a certain position specified in DC excitation mode for the period of (a), during which
the IP pin voltage decreases from Vrefout to 0.5 V. The time constant for the period is determined by CIP
and RST. After that, operation mode is switched to forced commutation mode (b) as shown above. The duty
cycle for DC excitation mode is determined according to the SC pin voltage. And after the IP pin voltage
falls to 0.5 V or lower, the duty cycle is determined according to the VSP pin voltage. When the rotational
frequency exceeds the forced commutation frequency specified with the status of the FST pin, the operation
mode is switched to the sensorless square-wave mode.
Preliminary
相关PDF资料 |
PDF描述 |
|---|---|
| TB6592FLG | BRUSH DC MOTOR CONTROLLER, 0.8 A, PQCC24 |
| TB6595FL | BRUSH DC MOTOR CONTROLLER, 0.8 A, PQCC36 |
| TB6598FN | STEPPER MOTOR CONTROLLER, 0.8 A, PDSO16 |
| TB6607FLG | STEPPER MOTOR CONTROLLER, 0.8 A, PQCC36 |
| TB6615PG | STEPPER MOTOR CONTROLLER, PDIP16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TB6582FG(ES) | 制造商:Toshiba America Electronic Components 功能描述: |
| TB6582FG(O,EL) | 功能描述:马达/运动/点火控制器和驱动器 Brushless DC Motor Controller RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB6582FG(OEL) | 制造商:Toshiba America Electronic Components 功能描述:BRUSHLESS DC MOTOR DRIVER 18V 0.2MA |
| TB6584AFNG(O,C8,EL | 功能描述:马达/运动/点火控制器和驱动器 Brushless Motor DRVR 3-Phase 1A 45V RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB6584AFNG(O,EL) | 功能描述:马达/运动/点火控制器和驱动器 3-Phase Brushless Driver IC 45V 1.8A RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。