- 您现在的位置：买卖IC网 > PDF目录225279 > TB6608FNG STEPPER MOTOR CONTROLLER, 0.8 A, PDSO20 PDF资料下载
参数资料
| 型号： | TB6608FNG |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 0.8 A, PDSO20 |
| 封装： | 0.225 INCH, 0.65 MM PITCH, PLASTIC, SSOP-20 |
| 文件页数： | 19/30页 |
| 文件大小： | 356K |
| 代理商： | TB6608FNG |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
TB6608FNG
2007-12-17
26
Application Circuit Example
Note 1: Capacitors for the power supply lines should be connected as close to the IC as possible.
Note 2: The STBY pin must be set Low upon powering on and off the device. Otherwise, a large current might
abruptly flow through the output pins.
Also, at the power-on, VM must be applied after applying VCC. At the power-off, VCC must be turned off after
turning off VM.
Usage Considerations
A large current might abruptly flow through the IC in case of a short-circuit across its outputs, a short-circuit to
power supply or a short-circuit to ground, leading to a damage of the IC. Also, the IC or peripheral parts may be
permanently damaged or emit smoke or fire resulting in injury especially if a power supply pin (VCC, VM) or an
output pin (AO1, AO2, BO1, BO2) is short-circuited to adjacent or any other pins.
These possibilities should be fully considered in the design of the output, VCC, VM and ground lines.
Install this IC correctly. If not, (e.g., installing it in the wrong position,) the IC may be damaged permanently.
Fuses should be connected to the power supply lines.
0.1
μF
47
μF
VCC = 3.3 V
Clock
CW/CCW
Reset
Enable
Standby
H/L
220
pF
VCC
MO
CK
CW/CCW
RESET
ENABLE
STBY
M1
M2
DCY
TQ
OSC
0.1
μF
47
μF
VM = 5 V
VM
AO1
AO2
CPU
I/O
BO1
BO2
RFA
RFB
Stepping
Motor
2
Ω
2
Ω
GND
TB6608FNG
相关PDF资料 |
PDF描述 |
|---|---|
| TBS22A | SINGLE COLOR LED |
| TBT4854 | Pigtailed PD for analog application |
| TBT4855 | Pigtailed PD for analog application |
| TBT4856 | Pigtailed PD for analog application |
| TBT48N3 | Pigtailed PD for analog application |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TB6608FNG(C8,EL,HJ | 制造商:Toshiba 功能描述:Cut Tape 制造商:Toshiba America Electronic Components 功能描述:2ph stepping motor driver 制造商:Toshiba 功能描述:Stepper Motor Driver 3.3V T/R |
| TB6608FNG(C8OEL,HZ | 功能描述:马达/运动/点火控制器和驱动器 2-phase stepping motor Drvr 15V RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB6608FNG(O,EL) | 功能描述:马达/运动/点火控制器和驱动器 Stepping Motor Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB6612FNG(O,C,8,EL | 功能描述:马达/运动/点火控制器和驱动器 15V Bridge Drvr for brushed DC motors RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB6612FNG(O,EL) | 功能描述:马达/运动/点火控制器和驱动器 Bridge Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。