参数资料
型号: TC110303ECTTR
厂商: Microchip Technology
文件页数: 7/16页
文件大小: 0K
描述: IC REG CTRLR BST PWM SOT23A-5
标准包装: 3,000
PWM 型: 控制器
输出数: 1
频率 - 最大: 345kHz
占空比: 92%
电源电压: 2 V ~ 10 V
降压:
升压:
回扫:
反相:
倍增器:
除法器:
Cuk:
隔离:
工作温度: -40°C ~ 85°C
封装/外壳: SC-74A,SOT-753
包装: 带卷 (TR)
TC110
3.7 Output Diode
For best results, use a Schottky diode such as the
MA735, 1N5817, MBR0520L or equivalent. Connect
the diode between the FB (or SENSE) input as close to
the IC as possible. Do not use ordinary rectifier diodes
since the higher threshold voltages reduce efficiency.
The two most significant losses in the N-channel
MOSFET are switching loss and I 2 R loss. To minimize
these, a transistor with low r DS ON and low CRSS should
be used.
Bipolar NPN transistors can be used, but care must be
taken when determining base current drive. Too little
current will not fully turn the transistor on, and result in
3.8
External Switching Transistor
Selection
unstable regulator operation and low efficiency. Too
high a base drive causes excessive power dissipation
in the transistor and increase switching time due to
The EXT output is designed to directly drive an
N-channel MOSFET or NPN bipolar transistor. N-
channel MOSFETs afford the highest efficiency
because they do not draw continuous gate drive
over-saturation. For peak efficiency, make R B as large
as possible, but still guaranteeing the switching transis-
tor is completely saturated when the minimum value of
h FE is used.
current, but are typically more expensive than bipolar
transistors. If using an N-channel MOSFET, the gate
3.9
Board Layout Guidelines
should be connected directly to the EXT output as
shown in Figure 3-1 and Figure 3-1. EXT is a compli-
mentary output with a maximum ON resistances of 43 ?
to V DD when high and 27 ? to ground when low. Peak
currents should be kept below 10mA.
When selecting an N-channel MOSFET, there are three
important parameters to consider: total gate charge
(Qg); ON resistance (r DS ON ) and reverse transfer
capacitance (CRSS). Qg is a measure of the total gate
capacitance that will ultimately load the EXT output.
Too high a Qg can reduce the slew rate of the EXT
output sufficiently to grossly lower operating efficiency.
Transistors with typical Qg data sheet values of 50nC
or less can be used. For example, the Si9410DY has a
Qg (typ) of 17nC @ V GS = 5V. This equates to a gate
current of:
I GATE MAX = f MAX x Qg = 115kHz x 17nC = 2mA
2002 Microchip Technology Inc.
As with all inductive switching regulators, the TC110
generates fast switching waveforms which radiate
noise. Interconnecting lead lengths should be mini-
mized to keep stray capacitance, trace resistance and
radiated noise as low as possible. In addition, the GND
pin, input bypass capacitor and output filter capacitor
ground leads should be connected to a single point.
The input capacitor should be placed as close to power
and ground pins of the TC110 as possible.
DS21355B-page 7
相关PDF资料
PDF描述
TC110331ECTTR IC REG CTRLR BST PWM SOT23A-5
TC110301ECTTR IC REG CTRLR BST PWM SOT23A-5
TC110333ECTTR IC REG CTRLR BST PWM SOT23A-5
TC110501ECTTR IC REG CTRLR BST PWM SOT23A-5
LD1-390-R INDUCTOR POWER 39UH 0.63A
相关代理商/技术参数
参数描述
TC110331ECT 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:PFM/PWM Step-Up DC/DC Controller
TC110331ECTTR 功能描述:开关变换器、稳压器与控制器 PFM/PWM Step-Up RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel
TC110333ECT 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:PFM/PWM Step-Up DC/DC Controller
TC110333ECTTR 功能描述:开关变换器、稳压器与控制器 PFM/PWM Step-Up RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel
TC1104 制造商:Thomas & Betts 功能描述:CABLE TIES