- 您现在的位置：买卖IC网 > PDF目录13509 > TC120503EHATR (Microchip Technology)IC REG BUCK 5V 0.6A 8SOP PDF资料下载
参数资料
| 型号： | TC120503EHATR |
| 厂商： | Microchip Technology |
| 文件页数： | 6/14页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 5V 0.6A 8SOP |
| 标准包装： | 1,000 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 5V |
| 输入电压： | 1.8 V ~ 10 V |
| 频率 - 开关： | 300kHz |
| 电流 - 输出： | 600mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.173"，4.40mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-SOP |
TC120
3.6
Low Power Shutdown Mode/Soft
3.9
External Switching Transistor
Start Input
The SHDN/SS input acts as both the shutdown control
and the node for the external soft start capacitor, which
is charged by an internal 1 μ A current source. A value
of 4700pF (100pF minimum) is recommended for the
soft start capacitor. Failure to do this may cause large
overshoot voltages and/or large inrush currents result-
ing in possible instability. The TC120 enters a low
power shutdown mode when SHDN/SS is brought low.
While in shutdown, the oscillator is disabled and the
output discharge switch is turned on, discharging the
output capacitor. Figure 3-3 shows the recommended
interface circuits to the SHDN/SS input. As shown, the
SHDN/SS input should be controlled using an open
collector (or open drain) device, such that the SHDN/
SS input is grounded for shutdown mode, and open-
circuited for normal operation (Figure 3-3a). If a CMOS
device is used to control shutdown (Figure 3-3b), the
value of R1 and C SS should be chosen such that the
voltage on SHDN/SS rises from ground to 0.65V in
Selection
EXT is a complimentary output with a maximum ON
resistances of 32 ? to V DD when high and 26 ? to
ground when low, at V OUT = 5V. It is designed to
directly drive a P-channel MOSFET (Figure 3-5). The
P-channel MOSFET selection is determined mainly by
the on-resistance, gate-source threshold and gate
charge requirements. Also, the drain-to-source and
gate-to-source breakdown voltage ratings must be
greater than V IN MAX . The total gate charge specification
should be less than 100nC for best efficiency. The
MOSFET must be capable of handling the required
peak inductor current, and should have a very low on-
resistance at that current. For example, a Si9430
MOSFET has a drain-to-source rating of -20V, and a
typical on-resistance r DS ON of 0.07 ? at 2A, with V GS =
-4.5V. (EXTW (Figure 3-6) may be gated with external
circuitry to add blanking, or as an auxiliary timing
signal.) Table 3-1 lists suggested components and
suppliers.
1.5msec (Figure 3-4). If shutdown is not used, C SS
must still be connected as shown in Figure 3-3c and
3.10
Board Layout Guidelines
Figure 3-3d. SHDN/SS may be pulled up with a resistor
(Figure 3-3c) as long as the values of R SS and C SS
provide the approximate charging characteristic on
power up shown in Figure 3-4. C SS only may also be
connected as shown in Figure 3-3d with C SS chosen at
4700pF (minimum 100pF).
As with all inductive switching regulators, the TC120
generates fast switching waveforms, which radiate
noise. Interconnecting lead lengths should be
minimized to keep stray capacitance, trace resistance
and radiated noise as low as possible. In addition, the
GND pin, input bypass capacitor and output filter
3.7
Undervoltage Lockout (UVLO)
capacitor ground leads should be connected to a single
point. The input capacitor should be placed as close to
The TC120 is disabled whenever V IN is below the
undervoltage lockout threshold. This threshold is equal
to the guaranteed minimum operating voltage for the
TC120 (i.e., 2.2V). When UVLO is active, the TC120 is
completely disabled.
power and ground pins of the TC120 as possible. The
length of the EXT trace must also be kept as short as
possible.
3.8
Short Circuit Protection
Upon detection of an output short circuit condition, the
TC120 reduces the PWM duty cycle to a minimum
value using its internal protection timer. The sequence
of events is as follows: when an output voltage
decrease to near zero is detected (as the result of an
overload), the internal (5msec) protection timer is
started. If the output voltage has not recovered to
nominal value prior to the expiration of the protection
timer, the TC120 is momentarily shut down by
dedicated, internal circuitry. Immediately following this
action, the soft start sequence is engaged in an attempt
to re-start the TC120. If the output short circuit is
removed, normal operation is automatically restored. If
the short circuit is still present, the timed self-shutdown
sequence described above is repeated.
DS21365B-page 6
2002 Microchip Technology Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| EMM15DTBD-S273 | CONN EDGECARD 30POS R/A .156 SLD |
| VI-24D-EX-F1 | CONVERTER MOD DC/DC 85V 75W |
| EMM15DTAN-S273 | CONN EDGECARD 30POS R/A .156 SLD |
| VI-24B-EX-F4 | CONVERTER MOD DC/DC 95V 75W |
| TC120333EHATR | IC REG BUCK 3.3V 0.6A 8SOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC1207D-100M | 制造商:PRODUCTWELL 制造商全称:PRODUCTWELL 功能描述:TOROID INDUCTORS |
| TC1207D-320M | 制造商:PRODUCTWELL 制造商全称:PRODUCTWELL 功能描述:TOROID INDUCTORS |
| TC1210A | 制造商:Thomas & Betts 功能描述:Fittings Connector 4inch Steel |
| TC12-11CGKWA | 制造商:Kingbright Corporation 功能描述:DOT MATRIX 1.2" CMN CATHODE GREEN 制造商:Kingbright Corporation 功能描述:DOT MATRIX, 1.2" CMN CATHODE, GREEN 制造商:Kingbright Corporation 功能描述:DOT MATRIX, 1.2" CMN CATHODE, GREEN; Display Dots x Lines:5 x 7; LED Color:Green; Luminous Intensity:73mcd; LED Display Type:Dot Matrix; Peak Wavelength:574nm; Forward Voltage:2.1V; Display Size:22.9mm x 39mm ;RoHS Compliant: Yes |
| TC12-11EWA | 功能描述:LED 显示器和配件 Dot Matrix Red 625nm Common Cathode RoHS:否 制造商:Avago Technologies 显示器类型:7 Segment 数位数量:2 字符大小:7.8 mm x 14.22 mm 照明颜色:Red 波长:628 nm 共用管脚:Common Anode 工作电压:2.05 V 工作电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 35 C 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。