- 您现在的位置：买卖IC网 > PDF目录85431 > TC1276-15ENBTR 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 PDF资料下载
参数资料
| 型号： | TC1276-15ENBTR |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| 封装： | SOT-23B, 3 PIN |
| 文件页数： | 4/6页 |
| 文件大小： | 60K |
| 代理商： | TC1276-15ENBTR |
4
TC1275/6/7-1 9/9/99
3-PIN MONITORS FOR 3.3V SYSTEMS
TC1276
TC1277
TC1275
Figure 6. Ensuring RESET Valid to VCC = 0V
TC1275
VCC
R1
100k
RESET
GND
Figure 5. Maximum Transient Duration vs.
Overdrive for Glitch Rejection at 25
°C
RESET COMPARATOR OVERDRIVE,
[V
CCTP - VCC](mV)
500
300
200
400
100
0
1
10
100
1000
MAXIMUM
TRANSIENT
DURATION
(
sec)
TA = +25°C
VTH
Duration
Overdrive
VCC
TC1275/6/7
t
F
t
RPD2
V
CC
V
CCTP
(MAX)
V
OH
RESET
V
CCTP
V
CCTP
(MIN)
RESET SLEWS WITH V
CC
Figure 4. Timing Diagram: Power Down (TC1277)
RESET Signal Integrity During Power-Down
The TC1275 RESET output is valid to VCC = 1.2V.
Below this voltage the output becomes an "open circuit"
and does not sink current. This means CMOS logic inputs
to the
P will be floating at an undetermined voltage. Most
digital systems are completely shutdown well above this
voltage. However, in situations where RESET must be
maintained valid to VCC = 0V, a pull-down resistor must be
connected from RESET to ground to discharge stray
capacitances and hold the output low (Figure 6). This
resistor value, though not critical, should be chosen such
that it does not appreciably load RESET under normal
operation (100k
will be suitable for most applications).
Similarly, a pull-up resistor to VCC is required for the
TC1277 to ensure a valid high RESET for VCC below 1.8V.
VCC Transient Rejection
The TC1275/6/7 provides accurate VCC monitoring and
reset timing during power-up, power-down, and brownout/sag
conditions, and rejects negative-going transients (glitches) on
the power supply line. Figure 5 shows the maximum transient
duration vs. maximum negative excursion (overdrive) for glitch
rejection. Any combination of duration and overdrive which lies
under the curve will not generate a reset signal. Combina-
tions above the curve are detected as a brownout or power-
down.
Transient immunity can be improved by adding a
capacitor in close proximity to the VCC pin of the TC1275/6/7.
相关PDF资料 |
PDF描述 |
|---|---|
| TQD100YGE-A82H | 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| TQD100YGE-AN82V | 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| TC54VN3202EZB713 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PBCY3 |
| TWR-3.3/4-15/250-D12 | 3-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| TS823CX5FRF | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC1276-20ENBTR | 功能描述:监控电路 3-Pin for 3.3V Syst RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| TC1276-5ENB | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:3-Pin Reset Monitors for 3.3V Systems |
| TC1276-5ENBTR | 功能描述:监控电路 3-Pin for 3.3V Syst RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| TC1276-XENB | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:3-Pin Reset Monitors for 3.3V Systems |
| TC1277 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:3-Pin Reset Monitors for 3.3V Systems |
发布紧急采购，3分钟左右您将得到回复。