- 您现在的位置：买卖IC网 > PDF目录98167 > TC1277-5ENB713 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 PDF资料下载
参数资料
| 型号： | TC1277-5ENB713 |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| 封装： | PLASTIC, SOT-23, 3 PIN |
| 文件页数： | 8/12页 |
| 文件大小： | 503K |
| 代理商： | TC1277-5ENB713 |
2007 Microchip Technology Inc.
DS21383C-page 5
TC1275/TC1276/TC1277
3.2
VCC Transient Rejection
The TC1275/TC1276/TC1277 provides accurate VCC
monitoring and reset timing during power-up, power-
down, and brownout/sag conditions, and rejects
negative-going transients (glitches) on the power
supply line. Figure 3-5 shows the maximum transient
duration vs. maximum negative excursion (overdrive)
for glitch rejection. Any combination of duration and
overdrive that lays under the curve will not generate a
reset signal. Combinations above the curve are
detected as a brownout or power-down. Transient
immunity can be improved by adding a capacitor in
close proximity to the VCC pin of the TC1275/TC1276/
TC1277.
3.3
RESET Signal Integrity During
Power-Down
The TC1275 RESET output is valid to VCC = 1.2V.
Below this voltage the output becomes an "open
circuit" and does not sink current. This means CMOS
logic inputs to the
μP will be floating at an undeter-
mined voltage. Most digital systems are completely
shut down well above this voltage. However, in situa-
tions where RESET must be maintained valid to
VCC = 0V, a pull-down resistor must be connected from
RESET to ground to discharge stray capacitances and
hold the output low (Figure 3-6). This resistor value,
though not critical, should be chosen such that it does
not appreciably load RESET under normal operation
(100 k
Ω will be suitable for most applications). Simi-
larly, a pull-up resistor to VCC is required for the
TC1277 to ensure a valid high RESET for VCC below
1.8V.
FIGURE 3-5:
Maximum Transient
Duration Vs. Overdrive For Glitch Rejection At
+25°C.
FIGURE 3-6:
ENSURING RESET VALID
TO VCC = 0V.
RESET COMPARATOR OVERDRIVE,
[V
CCTP - VCC] (mV)
500
300
200
400
100
0
1
10
100
1000
MAXIMUM
TRANSIENT
DURATION
(
μ
sec)
TA
°C
VTH
Duration
Overdrive
VCC
TC1275/6/7
TC1275
VCC
R1
100k
RESET
GND
相关PDF资料 |
PDF描述 |
|---|---|
| TC1275-5ENB | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| TC1276-15ENB713 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| TC1275-10ENB713 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| TC1275-15ENB713 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| TC1277-10ENB | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC1277-5ENBTR | 功能描述:监控电路 3-Pin for 3.3V Syst RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| TC1277-XENB | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:3-Pin Reset Monitors for 3.3V Systems |
| TC1278 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:3-Pin Reset Monitors for 5V Systems |
| TC1278_07 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:3-Pin Reset Monitors for 5V Systems |
| TC1278-10ENB | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:3-Pin Reset Monitors for 5V Systems |
发布紧急采购，3分钟左右您将得到回复。