- 您现在的位置：买卖IC网 > PDF目录272821 > TC3827-4.1VUART POWER SUPPLY SUPPORT CKT, PDSO8 PDF资料下载
参数资料
| 型号： | TC3827-4.1VUART |
| 元件分类： | 电源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封装： | MSOP-8 |
| 文件页数： | 5/9页 |
| 文件大小： | 122K |
| 代理商： | TC3827-4.1VUART |
5
Lithium-Ion Battery Charger
TC3827
TC3827-4 9/28/00
control loop changes from current limiting to voltage regula-
tion. If an external micro-controller determines battery con-
ditions are unsafe for charge it can toggle the shutdown pin
low and interrupt the charge cycle. Otherwise, once the pre-
determined cell voltage is reached the TC3827 shifts into a
constant-voltage mode (linear regulation) and a variable
charge current is applied as required to maintain the battery
cell voltage to within 1% accuracy of the cell voltage set-
point.
IMON – Charge Current Status
The IMON pin provides an output voltage that is propor-
tional to the battery charging current . It is an amplified
version of the sense resistor voltage drop that the current
loop uses to control the PMOS device. This voltage signal
can be applied to the input of an A/D Converter and used by
a controller to display information about the state of the
battery or charge current profile.
MODE – Charge Mode Status LED
The MODE pin indicates the battery charging mode. An
LED can be connected to the MODE for a visible indicator.
Alternatively, a pull-up resistor (typically 100k
) from the
interfacing logic supply to MODE provides a logic-level
output. The MODE pin will toggle LOW and the LED will
illuminate when the charger is in the current limited mode.
The MODE pin toggles to a high impedance state and the
LED will be off during constant-voltage mode charging or if
the battery is not connected. The MODE pin toggles at a
VOUT of VREG, typically.
APPLICATION CIRCUIT DESIGN
Due to the low efficiency of Linear Regulator Charging,
the most important factors are thermal design and cost,
which is a direct function of the input voltage, output current
and thermal impedance between the PMOS and the ambi-
ent cooling air. The worst-case situation is when the battery
is shorted since the PMOS has to dissipate the maximum
power. A tradeoff must be made between the charge cur-
rent, cost and thermal requirements of the charger. Higher
current requires a larger PMOS with more effective heat
dissipation leading to a more expensive design. Lowering
the charge current reduces cost by lowering the size of the
PMOS, possibly allowing a smaller package such as 6-Pin
SOT. The following designs consider both options.
Higher Current Option
The current sense resistor for the circuit shown in
Figure 1 is calculated by:
RSENSE = VCS /IMAX .
Where VCS is the current limit threshold voltage of
40mV to 75mV, 50mV typical. If IMAX = 1A is desired,
RSENSE = 50m.
Pre-regulated Input Voltage (5V
± 0%)
For this application, the required
θJA thermal imped-
ance is calculated as follows:
if:
the PMOS data sheet allows a max
junction temperature of TJMAX = 150°C,
then:
at 50
°C ambient with convection
cooling, the maximum allowed
junction temperature rise is:
TJMAX – TAMAX = 150°C – 50°C = 100°C.
θJA = T/(IOx k x VIN) = 100/(1 x 0.46 x 5.5)
= 39.5
°C/W
This k factor is: k = ISC/IMAX ≈ 0.46.
This thermal impedance can be realized using the
transistor shown in Figure 1 when mouted to a heat sink.
The
θSA or thermal impedance of a suitable heatsink is
calculated below:
θSA ≤ (θJA – θJC – θCS) = 39.5 – 2.5 – 0.3 = 36.7°C/W
Where the
θJC, or junction-to-case thermal impedance
is for the PMOS from the PMOS data sheet. A low cost
heatsink is Thermalloy type PF430, with a
θSA = +25.3°C/W.
相关PDF资料 |
PDF描述 |
|---|---|
| TC6503P005VCT | SPECIALTY ANALOG CIRCUIT, PDSO5 |
| TS12A4517DG4 | 1-CHANNEL, SGL POLE SGL THROW SWITCH, PDSO8 |
| TL431ID5-G | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 2.495 V, PDSO5 |
| TL4051BIDBZT | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.212 V, PDSO3 |
| TL4051CIDCKRG4 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.212 V, PDSO5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC3873 | 制造商:TRANSCOM 制造商全称:TRANSCOM 功能描述:5.25 - 5.875 GHz 3W prematched FETs |
| TC3875A-V19 | 制造商:HENKEL 功能描述:ADHESIVE, ANAEROBIC, CONTAINER, 30ML, Adhesive Type:Anaerobic, Chemical Color:Ye 制造商:Henkel Corporation / Loctite 功能描述:ADHESIVE, ANAEROBIC, CONTAINER, 30ML, Adhesive Type:Anaerobic, Chemical Color:Yellow, Dispensing Method:Container, Volume:30ml, Color:Yellow , RoHS Compliant: Yes |
| TC3875B-V19 | 制造商:Henkel Corporation / Loctite 功能描述:ADHESIVE, ANAEROBIC, SYRINGE, 30ML; Adhesive Type:Anaerobic; Chemical Color:Yellow; Dispensing Method:Syringe; Volume:30ml; Chemical Solution:Acrylate; Color:Yellow ;RoHS Compliant: Yes |
| TC3876A-V19 | 制造商:HENKEL 功能描述:ADHESIVE, ANAEROBIC, SYRINGE, 30ML, Adhesive Type:Anaerobic, Chemical Color:Yell |
| TC3876B-V19 | 制造商:HENKEL 功能描述:ADHESIVE, ANAEROBIC, SYRINGE, 30ML, Adhesive Type:Anaerobic, Chemical Color:Blue |
发布紧急采购，3分钟左右您将得到回复。