- 您现在的位置：买卖IC网 > PDF目录150820 > TC647VPA BRUSHLESS DC MOTOR CONTROLLER, PDIP8 PDF资料下载
参数资料
| 型号： | TC647VPA |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, PDIP8 |
| 封装： | 0.300 INCH, PLASTIC, DIP-8 |
| 文件页数： | 6/28页 |
| 文件大小： | 478K |
| 代理商： | TC647VPA |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
TC647
DS21447C-page 14
2002 Microchip Technology Inc.
FIGURE 5-7:
Output Drive Transistor Circuit Topologies.
FIGURE 5-8:
Powering the Fan from a
-12V Supply.
5.6
Latch-Up Considerations
As with any CMOS IC, the potential exists for latch-up
if signals are applied to the device which are outside
the power supply range. This is of particular concern
during power-up if the external circuitry (such as the
sensor network, VMIN divider or shutdown circuit) is
powered by a supply different from that of the TC647.
Care should be taken to ensure that the TC647’s VDD
supply powers up first. If possible, the networks
attached to VIN and VMIN should connect to the VDD
supply at the same physical location as the IC itself.
Even if the IC and any external networks are powered
by the same supply, physical separation of the connect-
ing points can result in enough parasitic capacitance
and/or inductance in the power supply connections to
delay one power supply “routing” versus another.
5.7
Power Supply Routing and
Bypassing
Noise present on the VIN and VMIN inputs may cause
erroneous operation of the FAULT output. As a result,
these inputs should be bypassed with a 0.01 F capac-
itor mounted as close to the package as possible. This
is particularly true of VIN, which is usually driven from a
high impedance source (such as a thermistor). In addi-
tion, the VDD input should be bypassed with a 1 F
capacitor. Ground should be kept as short as possible.
To keep fan noise off the TC647 ground pin, individual
ground returns for the TC647 and the low side of the
fan current sense resistor should be used.
Design Example
Step 1. Calculate R1 and R2 based on using an NTC
having a resistance of 10 k
at TMIN (25°C)
and 4.65 k
R1 = 20.5 k
R2 = 3.83 k
Step 2. Set minimum fan speed VMIN = 1.8V.
Limit the divider current to 100 A from which
R5 = 33 k and R6 = 18 k
Step 3. Design the output circuit.
Maximum fan motor current = 250 mA.
Q1 beta is chosen at 50 from which
R7 = 800.
Q1
Q2
GND
VDD
RSENSE
RBASE
VOUT
Fan
a) Single Bipolar Transistor
Q1
GND
VDD
RSENSE
VOUT
C) N-Channel MOSFET
GND
VDD
RSENSE
RBASE
Fan
b) Darlington Transistor Pair
Fan
GND
+5V
Q1 *
VDD
VOUT
TC647
Fan
R2 *
2.2 k
R3 *
2.2
*Note: Value depends on the specific application and is shown for example only.
D1
12.0V
Zener
-12V
R4 *
10 k
相关PDF资料 |
PDF描述 |
|---|---|
| TC1271ASBVCT | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TC1271ASBVRC | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO4 |
| TL7726QDRG4 | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| TC1028CUA723 | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| TPS61105PW | SWITCHING REGULATOR, 800 kHz SWITCHING FREQ-MAX, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC647VUA | 功能描述:马达/运动/点火控制器和驱动器 w/Fault Dtct RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TC647VUATR | 功能描述:马达/运动/点火控制器和驱动器 w/Fault Dtct RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TC648 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Fan Speed Controller with Auto-Shutdown and Over-Temperature Alert |
| TC648_13 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Fan Speed Controller with Auto-Shutdown and Over-Temperature Alert |
| TC648B | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:PWM Fan Speed Controllers With Auto-Shutdown, Fan Restart and FanSense⑩ Technology for Fault Detection |
发布紧急采购，3分钟左右您将得到回复。