参数资料
型号: TC7107ARCKW
元件分类: ADC
英文描述: 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PQFP44
封装: REVERSE, PLASTIC, QFP-44
文件页数: 7/26页
文件大小: 623K
代理商: TC7107ARCKW
2002 Microchip Technology Inc.
DS21455B-page 15
TC7106/A/TC7107/A
FIGURE 8-2:
COMMON MODE VOLTAGE REMOVED IN BATTERY OPERATION WITH
VIN- = ANALOG COMMON
The analog common pin serves to set the analog section
reference or common point. The TC7106A is specifically
designed to operate from a battery, or in any measure-
ment system where input signals are not referenced
(float), with respect to the TC7106A power source. The
analog common potential of V+ – 3.0V gives a 6V end of
battery life voltage. The common potential has a 0.001%
voltage coefficient and a 15
output impedance.
With sufficiently high total supply voltage (V+ – V- >
7.0V), analog common is a very stable potential with
excellent temperature stability, typically 20ppm/°C.
This potential can be used to generate the reference
voltage. An external voltage reference will be unneces-
sary in most cases because of the 50ppm/°C maximum
temperature coefficient. See Internal Voltage Refer-
ence discussion.
8.4
TEST (Pin 37)
The TEST pin potential is 5V less than V+. TEST may
be used as the negative power supply connection for
external CMOS logic. The TEST pin is tied to the inter-
nally generated negative logic supply (Internal Logic
Ground) through a 500
resistor in the TC7106A. The
TEST pin load should be no more than 1mA.
If TEST is pulled to V+ all segments plus the minus sign
will be activated. Do not operate in this mode for more
than
several
minutes
with
the
TC7106A.
With
TEST = V+, the LCD segments are impressed with a
DC voltage which will destroy the LCD.
The TEST pin will sink about 10mA when pulled to V+.
8.5
Internal Voltage Reference
The analog common voltage temperature stability has
been significantly improved (Figure 8-3). The “A” ver-
sion of the industry standard circuits allow users to
upgrade old systems and design new systems without
external voltage references. External R and C values
do not need to be changed. Figure 8-4 shows analog
common supplying the necessary voltage reference for
the TC7106A/TC7107A.
FIGURE 8-3:
ANALOG COMMON
TEMPERATURE
COEFFICIENT
FIGURE 8-4:
INTERNAL VOLTAGE
REFERENCE
CONNECTION
VBUF
CAZ
VINT
BP
POL
Segment
Drive
OSC1
OSC3
OSC2
V-
V+
VREF+
VREF-
Analog
Common
V-
V+
V-
V+
GND
Measured
System
Power
Source
9V
LCD Display
TC7106A
+
VIN-
VIN+
Typical
No Maximum Specified
No
Maximum
Specified
No
Maximum
Specified
Typical
200
180
160
140
120
100
80
60
40
20
0
Temperature
Coefficient
(ppm/
°C)
ICL7136
TC
7106A
ICL7106
Maximum
Limit
V-
Analog
Common
TC7106A
TC7107A
VREF+
32
35
36
24k
1k
VREF-
VREF
1
Set VREF = 1/2 VFULL SCALE
V+
相关PDF资料
PDF描述
TC7106RCKW 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PQFP44
TC7106RCLW 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PQCC44
TC7106ARCKW 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PQFP44
TC7106ARCLW 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PQCC44
TC7106ARIPL 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PDIP40
相关代理商/技术参数
参数描述
TC7107ARCPL 功能描述:LED显示驱动器 w/LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
TC7107CKW 功能描述:LED显示驱动器 w/LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
TC7107CKW713 功能描述:LED显示驱动器 w/LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
TC7107CLW 功能描述:LED显示驱动器 w/LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
TC7107CLW713 功能描述:LED显示驱动器 w/LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube