- 您现在的位置：买卖IC网 > PDF目录98172 > TC7107RCPL 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PDIP40 PDF资料下载
参数资料
| 型号： | TC7107RCPL |
| 元件分类： | ADC |
| 英文描述： | 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PDIP40 |
| 封装： | REVERSE, PLASTIC, DIP-40 |
| 文件页数： | 6/26页 |
| 文件大小： | 623K |
| 代理商： | TC7107RCPL |
TC7106/A/TC7107/A
DS21455B-page 14
2002 Microchip Technology Inc.
Thedifferential reference canalsobe usedwhenadig-
ital zero reading is required when VIN is not equal to
zero. This is common in temperature measuring instru-
mentation. A compensating offset voltage can be
applied between analog common and VIN-. The trans-
ducer output is connected between VIN+ and analog
common.
The internal voltage reference potential available at
analog common will normally be used to supply the
converter's reference. This potential is stable when-
ever the supply potential is greater than approximately
7V. In applications where an externally generated ref-
erence voltage is desired, refer to Figure 7-1.
FIGURE 7-1:
EXTERNAL REFERENCE
8.0
DEVICE PIN FUNCTIONAL
DESCRIPTION
8.1
Differential Signal Inputs
VIN+(Pin31), VIN-(Pin 30)
The TC7106A/7017A is designed with true differential
inputs and accepts input signals within the input stage
common mode voltage range (VCM). The typical range
is V+ – 1.0 to V+ + 1V. Common mode voltages are
removed from the system when the TC7106A/
TC7107A operates from a battery or floating power
source (isolated from measured system) and VIN-is
connected to analog common (VCOM) (see Figure 8-2).
In systems where Common mode voltages exist, the
86dB Common mode rejection ratio minimizes error.
Common mode voltages do, however, affect the inte-
grator output level. Integrator output saturation must be
prevented. A worst case condition exists if a large pos-
itive VCM exists in conjunction with a full scale negative
differential signal. The negative signal drives the inte-
grator output positive along with VCM (see Figure 8-1).
For such applications the integrator output swing can
be reduced below the recommended 2.0V full scale
swing. The integrator output will swing within 0.3V of
V+ or V- without increasing linearity errors.
FIGURE 8-1:
COMMON MODE
VOLTAGE REDUCES
AVAILABLE INTEGRATOR
SWING (VCOM ≠ VIN)
8.2
Differential Reference
VREF+(Pin36), VREF-(Pin 35)
The reference voltage can be generated anywhere
within the V+ to V- power supply range.
To prevent rollover type errors being induced by large
Common mode voltages, CREF should be large com-
pared to stray node capacitance.
The TC7106A/TC7107A circuits have a significantly
lower analog common temperature coefficient. This
gives a very stable voltage suitable for use as a refer-
ence. The temperature coefficient of analog common is
20ppm/°C typically.
8.3
Analog Common(Pin32)
The analog common pin is set at a voltage potential
approximately 3.0V below V+. The potential is between
2.7V and 3.35V below V+. Analog common is tied inter-
nally to the N channel FET capable of sinking 20mA.
This FET will hold the common line at 3.0V should an
external load attempt to pull the common line toward
V+. Analog common source current is limited to 10
A.
Analog common is, therefore, easily pulled to a more
negative voltage (i.e., below V+ – 3.0V).
The TC7106A connects the internal VIN+and VIN-
inputs to analog common during the auto-zero cycle.
During the reference integrate phase, VIN- is con-
nected to analog common. If VIN- is not externally con-
nected to analog common, a Common mode voltage
exists. This is rejected by the converter's 86dB Com-
mon mode rejection ratio. In battery operation, analog
common and VIN- are usually connected, removing
Common mode voltage concerns. In systems where V-
is connected to the power supply ground, or to a given
voltage, analog common should be connected to VIN-.
TC7106A
TC7107A
6.8V
Zener
IZ
V+
1.2V
Ref
Common
TC7106A
TC7107A
6.8k
20k
VREF+
VREF-
VREF+
VREF-
(a)(b)
V+
RI
+
–
VIN
VCM
CI
Integrator
VI =
[
VCM – VIN
Input Buffer
CI = Integration Capacitor
RI = Integration Resistor
4000
FOSC
TI = Integration Time =
Where:
VI
–
+
–
+
TI
RI CI
相关PDF资料 |
PDF描述 |
|---|---|
| TC7106ARIJL | 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, CDIP40 |
| TC7107CKW | 1-CH DUAL-SLOPE ADC, PQFP44 |
| TC7107CLW | 1-CH DUAL-SLOPE ADC, PQCC44 |
| TC7107IJL | 1-CH DUAL-SLOPE ADC, CDIP40 |
| TC7106ACLW | 1-CH DUAL-SLOPE ADC, PQCC44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC7109 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:12-Bit レA-Compatible Analog-to-Digital Converters |
| TC7109_13 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:12-Bit ??-A-Compatible Analog-to-Digital Converters |
| TC7109A | 制造商:TELCOM 制造商全称:TelCom Semiconductor, Inc 功能描述:12-BIT UP-COMPATIBLE ANALOG-TO-DIGITAL CONVERTERS |
| TC7109ACKW | 功能描述:模数转换器 - ADC 13 Bit Fast Recovery RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| TC7109ACKW713 | 功能描述:模数转换器 - ADC 13 Bit Fast Recovery RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。