- 您现在的位置：买卖IC网 > PDF目录98176 > TC7116ACKWTR 1-CH 22-BIT DUAL-SLOPE ADC, PARALLEL ACCESS, PQFP44 PDF资料下载
参数资料
| 型号： | TC7116ACKWTR |
| 元件分类： | ADC |
| 英文描述： | 1-CH 22-BIT DUAL-SLOPE ADC, PARALLEL ACCESS, PQFP44 |
| 封装： | PLASTIC, QFP-44 |
| 文件页数： | 4/24页 |
| 文件大小： | 410K |
| 代理商： | TC7116ACKWTR |
TC7116/A/TC7117/A
DS21457C-page 12
2006 Microchip Technology Inc.
4.0
COMPONENT VALUE
SELECTION
4.1
Auto-Zero Capacitor
The size of the auto-zero capacitor has some influence
on system noise. For 200mV full scale, where noise is
very important, a 0.47
μF capacitor is recommended.
On the 2V scale, a 0.047
μF capacitor increases the
speed of recovery from overload and is adequate for
noise on this scale.
4.2
Reference Capacitor
A 0.1
μF capacitor is acceptable in most applications.
However, where a large Common mode voltage exists
(i.e., the VIN- pin is not at analog common), and a
200mV scale is used, a larger value is required to pre-
vent rollover error. Generally, 1
μF will hold the rollover
error to 0.5 count in this instance.
4.3
Integrating Capacitor
The integrating capacitor should be selected to give the
maximum voltage swing that ensures tolerance buildup
will not saturate the integrator swing (approximately
0.3V from either supply). In the TC7116/TC7116A or
the TC7117/TC7117A, when the analog common is
used as a reference, a nominal ±2V full scale integrator
swing is acceptable. For the TC7117/TC7117A, with
±5V supplies and analog common tied to supply
ground, a ±3.5V to ±4V swing is nominal. For 3 read-
ings per second (48kHz clock), nominal values for CINT
are 0.22
μ1F and 0.10μF, respectively. If different oscil-
lator frequencies are used, these values should be
changed in inverse proportion to maintain the output
swing. The integrating capacitor must have low dielec-
tric absorption to prevent rollover errors. Polypropylene
capacitors are recommended for this application.
4.4
Integrating Resistor
Both the buffer amplifier and the integrator have a class
A output stage with 100
μA of quiescent current. They
can supply 20
μA of drive current with negligible non-
linearity. The integrating resistor should be large
enough to remain in this very linear region over the
input voltage range, but small enough that undue leak-
age requirements are not placed on the PC board. For
2V full scale, 470k
Ω is near optimum and, similarly,
47k
Ω for 200mV full scale.
4.5
Oscillator Components
For all frequency ranges, a 100k
Ω resistor is recom-
mended; the capacitor is selected from the equation:
EQUATION 4-1:
For a 48kHz clock (3 readings per second), C = 100pF.
4.6
Reference Voltage
To generate full scale output (2000 counts), the analog
input requirement is VIN = 2VREF. Thus, for the 200mV
and 2V scale, VREF should equal 100mV and 1V,
respectively. In many applications, where the ADC is
connected to a transducer, a scale factor exists
between the input voltage and the digital reading. For
instance, in a measuring system, the designer might like
to have a full scale reading when the voltage from the
transducer is 700mV. Instead of dividing the input down
to 200mV, the designer should use the input voltage
directly and select VREF = 350mV. Suitable values for
integrating resistor and capacitor would be 120kW and
0.22
μF. This makes the system slightly quieter and also
avoids a divider network on the input. The TC7117/
TC7117A, with ±5V supplies, can accept input signals
up to ±4V. Another advantage of this system is when a
digital reading of zero is desired for VIN ≠ 0. Tempera-
ture and weighing systems with a variable tare are
examples. This offset reading can be conveniently gen-
erated by connecting the voltage transducer between
VIN+ and analog common, and the variable (or fixed)
offset voltage between analog common and VIN-.
f
0.45
RC
-------
=
相关PDF资料 |
PDF描述 |
|---|---|
| TC7116ACLWTR | 1-CH 22-BIT DUAL-SLOPE ADC, PARALLEL ACCESS, PQCC44 |
| TC7117CLWTR | 1-CH 22-BIT DUAL-SLOPE ADC, PARALLEL ACCESS, PQCC44 |
| TC7116IPL | 1-CH DUAL-SLOPE ADC, PDIP40 |
| TC7117ACPI | 1-CH DUAL-SLOPE ADC, PDIP40 |
| TC7117IPL | 1-CH DUAL-SLOPE ADC, PDIP40 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC7116ACLW | 功能描述:LCD 驱动器 w/Hold RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| TC7116ACLW713 | 功能描述:LCD 驱动器 w/Hold RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| TC7116ACPL | 功能描述:LCD 驱动器 w/Hold RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| TC7116AIJL | 功能描述:LCD 驱动器 3-1/2 Digit A/D w/ Hold RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| TC7116CKW | 功能描述:LCD 驱动器 w/Hold RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。