- 您现在的位置：买卖IC网 > PDF目录98174 > TC7116ACPL 1-CH 13-BIT DUAL-SLOPE ADC, ACCESS, PDIP40 PDF资料下载
参数资料
| 型号： | TC7116ACPL |
| 元件分类： | ADC |
| 英文描述： | 1-CH 13-BIT DUAL-SLOPE ADC, ACCESS, PDIP40 |
| 封装： | PLASTIC, DIP-40 |
| 文件页数： | 3/17页 |
| 文件大小： | 221K |
| 代理商： | TC7116ACPL |
11
3-1/2 DIGIT ANALOG-TO-DIGITAL
CONVERTERS WITH HOLD
TC7116
TC7116A
TC7117
TC7117A
COMPONENT VALUE SELECTION
Auto-Zero Capacitor
The size of the auto-zero capacitor has some influ-
ence on system noise. For 200mV full scale, where noise
is very important, a 0.47
F capacitor is recommended. On
the 2V scale, a 0.047
F capacitor increases the speed of
recovery from overload and is adequate for noise on this
scale.
Reference Capacitor
A 0.1
F capacitor is acceptable in most applications.
However, where a large common-mode voltage exists
(i.e., the V
–
IN pin is not at analog common), and a 200-mV
scale is used, a larger value is required to prevent roll-over
error. Generally, 1
F will hold the roll-over error to 0.5 count
in this instance.
Integrating Capacitor
The integrating capacitor should be selected to give the
maximum voltage swing that ensures tolerance buildup will
not saturate the integrator swing (approximately 0.3V from
either supply). In the TC7116/TC7116A or the TC7117/
TC7117A, when the analog common is used as a reference,
a nominal
±2V full- scale integrator swing is acceptable. For
the TC7117/TC7117A, with
±5V supplies and analog com-
mon tied to supply ground, a
±3.5V to ±4V swing is nominal.
For 3 readings per second (48kHz clock), nominal values
for CINT are 0.221F and 0.10F, respectively. If different
oscillator frequencies are used, these values should be
changed in inverse proportion to maintain the output swing.
The integrating capacitor must have low dielectric ab-
sorption to prevent roll-over errors. Polypropylene capaci-
tors are recommended for this application.
Integrating Resistor
Both the buffer amplifier and the integrator have a class
A output stage with 100
A of quiescent current. They can
supply 20
A of drive current with negligible nonlinearity.
The integrating resistor should be large enough to remain
in this very linear region over the input voltage range, but
small enough that undue leakage requirements are not
placed on the PC board. For 2V full scale, 470k
is near
optimum and, similarly, 47k
for 200mV full scale.
Oscillator Components
For all frequency ranges, a 100k
resistor is recom-
mended; the capacitor is selected from the equation:
For a 48 kHz clock (3 readings per second), C = 100pF.
Figure 10. Negative Power Supply Generation With TC7660
VREF
+
V
+
TC7117
TC7117A
36
10
F
VIN
+
VIN
–
COM
GND
32
31
30
21
10
F
VIN
V
–
(–5V)
5
3
8
2
4
+5V
35
TC7660
26
+
–
TC04
LED
DRIVE
Reference Voltage
To generate full-scale output (2000 counts), the analog
input requirement is VIN = 2 VREF. Thus, for the 200mV and
2V scale, VREF should equal 100mV and 1V, respectively. In
many applications, where the ADC is connected to a trans-
ducer, a scale factor exists between the input voltage and
the digital reading. For instance, in a measuring system the
designer might like to have a full-scale reading when the
voltage from the transducer is 700mV. Instead of dividing
the input down to 200 mV, the designer should use the input
voltage directly and select VREF = 350mV. Suitable values
for integrating resistor and capacitor would be 120k
and
0.22
F. This makes the system slightly quieter and also
avoids a divider network on the input. The TC7117/TC7117A,
with
±5V supplies, can accept input signals up to ±4V.
Another advantage of this system is when a digital reading
of zero is desired for VIN ≠ 0. Temperature and weighing
systems with a variable tare are examples. This offset
reading can be conveniently generated by connecting the
voltage transducer between V
+
IN and analog common, and
the variable (or fixed) offset voltage between analog com-
mon and V
–
IN.
TC7117/TC7117A POWER SUPPLIES
The TC7117/TC7117A are designed to operate from
±5V supplies. However, if a negative supply is not available,
it can be generated with a TC7660 DC-to-DC converter and
two capacitors. Figure 10 shows this application.
In selected applications, a negative supply is not re-
quired. The conditions for using a single +5V supply are:
(1) The input signal can be referenced to the center of
the common-mode range of the converter.
(2) The signal is less than
±1.5V.
(3) An external reference is used.
45
RC
f =
.
相关PDF资料 |
PDF描述 |
|---|---|
| TC7116AIJL | 1-CH 13-BIT DUAL-SLOPE ADC, ACCESS, CDIP40 |
| TC7116IJL | 1-CH 13-BIT DUAL-SLOPE ADC, ACCESS, CDIP40 |
| TC7116ACLWRT | 1-CH DUAL-SLOPE ADC, ACCESS, PQCC44 |
| TC7116CLWRT | 1-CH DUAL-SLOPE ADC, ACCESS, PQCC44 |
| TC7116CLWTR | 1-CH 13-BIT DUAL-SLOPE ADC, PQCC44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC7116AIJL | 功能描述:LCD 驱动器 3-1/2 Digit A/D w/ Hold RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| TC7116CKW | 功能描述:LCD 驱动器 w/Hold RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| TC7116CKW713 | 功能描述:LCD 驱动器 w/Hold RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| TC7116CLW | 功能描述:LCD 驱动器 w/Hold RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| TC7116CLW713 | 功能描述:LCD 驱动器 w/Hold RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。