- 您现在的位置：买卖IC网 > PDF目录98179 > TC7135CBUTR 1-CH DUAL-SLOPE ADC, PQFP64 PDF资料下载
参数资料
| 型号： | TC7135CBUTR |
| 元件分类： | ADC |
| 英文描述： | 1-CH DUAL-SLOPE ADC, PQFP64 |
| 封装： | PLASTIC, MS-022-BE, MQFP-64 |
| 文件页数： | 4/24页 |
| 文件大小： | 471K |
| 代理商： | TC7135CBUTR |
TC7135
DS21460C-page 12
2004 Microchip Technology Inc.
6.0
TYPICAL APPLICATIONS
6.1
Component Value Selection
6.1.1
INTEGRATING RESISTOR
The integrating resistor RINT is determined by the full-
scale input voltage and the output current of the buffer
used to charge the integrator capacitor (CINT). Both the
buffer amplifier and the integrator have a class A output
stage, with 100 A of quiescent current. A 20 A drive
current gives negligible linearity errors. Values of 5 A
to 40 A give good results. The exact value of an
integrating resistor for a 20 A current is easily
calculated.
EQUATION 6-1:
6.1.2
INTEGRATING CAPACITOR (CINT)
The product of integrating resistor and capacitor should
be selected to give the maximum voltage swing that
ensures the tolerance build-up will not saturate the
integrator swing (approximately 0.3V from either
supply). For ±5V supplies and ANALOG COMMON tied
to supply ground, a ±3.5V to ±4V full scale integrator
swing
is
adequate.
A
0.10 F
to
0.47 F
is
recommended. In general, the value of CINT is given
by:
EQUATION 6-2:
A very important characteristic of the integrating
capacitor CINT is that it has low dielectric absorption to
prevent rollover or ratiometric errors. A good test for
dielectric absorption is to use the capacitor with the
input tied to the reference. This ratiometric condition
should read half scale 0.9999, with any deviation
probably due to dielectric absorption. Polypropylene
capacitors give undetectable errors at reasonable cost.
Polystyrene and polycarbonate capacitors may also be
used in less critical applications.
6.1.3
AUTO-ZERO AND REFERENCE
CAPACITORS
The size of the auto-zero capacitor has some influence
on the noise of the system, with a larger capacitor
reducing the noise. The reference capacitor should be
large enough such that stray capacitance to ground
from its nodes is negligible.
The dielectric absorption of the reference and auto-
zero capacitors are only important at power-on or when
the circuit is recovering from an overload. Smaller or
cheaper capacitors can be used if accurate readings
are not required for the first few seconds of recovery.
6.1.4
REFERENCE VOLTAGE
The analog input required to generate a full-scale
output is VIN = 2 VREF.
The stability of the reference voltage is a major factor in
the overall absolute accuracy of the converter. For this
reason, it is recommended that a high-quality reference
be used where high-accuracy absolute measurements
are being made.
6.2
Conversion Timing
6.2.1
LINE FREQUENCY REJECTION
A signal integration period at a multiple of the 60 Hz
line frequency will maximize 60 Hz “line noise”
rejection. A 100 kHz clock frequency will reject 50 Hz,
60 Hz and 400 Hz noise. This corresponds to five
readings per second (see Table 6-1 and Table 6-2).
TABLE 6-1:
CONVERSION RATE VS.
CLOCK FREQUENCY
R
INT
Full Scale Voltage
20
A
--------------------------------------------
=
C
IN T
10 000
,
clock period
×
[] I
IN T
×
integrator output voltage swing
---------------------------------------------------------------------------
=
10 000
,
() clock period
() 20A
×
integrator output voltage swing
------------------------------------------------------------------------------
=
Oscillator Frequency
(kHz)
Conversion Rate
(Conv./Sec.)
100
2.5
120
3
200
5
300
7.5
400
10
800
20
1200
30
相关PDF资料 |
PDF描述 |
|---|---|
| TC7135CKW | 1-CH DUAL-SLOPE ADC, PQFP64 |
| TC7135CLITR | 1-CH DUAL-SLOPE ADC, PQCC28 |
| TC7135CPI | 1-CH DUAL-SLOPE ADC, PDIP28 |
| TC7135CBU | 1-CH DUAL-SLOPE ADC, PQFP64 |
| TC7135CLI713 | 1-CH DUAL-SLOPE ADC, PQCC28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC7135CKW | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:4-1/2 Digit A/D Converter |
| TC7135CLI | 功能描述:LED显示驱动器 4-1/2 Digit A/D BCD RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| TC7135CLI713 | 功能描述:LED显示驱动器 4-1/2 Digit A/D BCD RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| TC7135CPI | 功能描述:LED显示驱动器 4-1/2 Digit A/D BCD RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| TC7135CPL | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:4-1/2 Digit A/D Converter |
发布紧急采购，3分钟左右您将得到回复。