- 您现在的位置：买卖IC网 > PDF目录98179 > TC7136ACKW 1-CH DUAL-SLOPE ADC, PQFP44 PDF资料下载
参数资料
| 型号： | TC7136ACKW |
| 元件分类： | ADC |
| 英文描述： | 1-CH DUAL-SLOPE ADC, PQFP44 |
| 封装： | PLASTIC, QFP-44 |
| 文件页数： | 4/22页 |
| 文件大小： | 410K |
| 代理商： | TC7136ACKW |
TC7136/TC7136A
DS21461C-page 12
2005 Microchip Technology Inc.
An exact expression for CINT is:
EQUATION 6-1:
CINT must have low dielectric absorption to minimize
rollover
error.
A
polypropylene
capacitor
is
recommended.
6.4
Integrating Resistor (RINT)
The input buffer amplifier and integrator are designed
with Class A output stages. The output stage idling cur-
rent is 6
μA. The integrator and buffer can supply 1μA
drive currents with negligible linearity errors. RINT is
chosen to remain in the output stage linear drive
region, but not so large that PC board leakage currents
induce errors. For a 200mV full scale, RINT is 180kΩ. A
2V full scale requires 1.8M
Ω (see Table 6-1).
TABLE 6-1:
Note:
FOSC = 48kHz (3 reading per sec).
ROSC = 180kΩ, COSC = 50pF.
6.5
Oscillator Components
COSC should be 50pF. ROSC is selected from the
equation:
EQUATION 6-2:
Note that FOSC is ÷ 4 to generate the TC7136A's inter-
nal clock. The backplane drive signal is derived by
dividing FOSC by 800.
To achieve maximum rejection of 60Hz noise pickup,
the signal integrate period should be a multiple of
60Hz. Oscillator frequencies of 240kHz, 120kHz,
80kHz, 60kHz, 40kHz, etc. should be selected. For
50Hz rejection, oscillator frequencies of 200kHz,
100kHz, 66-2/3kHz, 50kHz, 40kHz, etc. would be suit-
able. Note that 40kHz (2.5 readings per second) will
reject both 50Hz and 60Hz.
6.6
Reference Voltage Selection
A full scale reading (2000 counts) requires the input
signal be twice the reference voltage.
Note:
*VREF = 2VREF.
In some applications, a scale factor other than unity
may exist between a transducer output voltage and the
required digital reading. Assume, for example, a pres-
sure transducer output for 2000 lb/in2 is 400mV. Rather
than dividing the input voltage by two, the reference
voltage should be set to 200mV. This permits the trans-
ducer input to be used directly. The differential refer-
ence can also be used when a digital zero reading is
required, when VIN is not equal to zero. This is common
in temperature measuring instrumentation. A compen-
sating offset voltage can be applied between analog
common and VIN-. The transducer output is connected
between VIN+ and analog common.
Component
Value
Nominal Full Scale Voltage
200mV
2V
CAZ
0.47
μF
0.1
μF
RINT
180k
Ω
1.8M
Ω
CINT
0.047
μF
0.047
μF
(4000)
1
FOSC
CINT =
VFS
RINT
VINT
Where:
FOSC = Clock frequency at Pin 38
VFS = Full scale input voltage
RINT = Integrating resistor
VINT = Desired full scale integrator output swing
Required Full Scale Voltage*
VREF
200mV
100mV
2V
1V
FOSC =
0.45
RC
相关PDF资料 |
PDF描述 |
|---|---|
| TC7136ACKW713 | 1-CH DUAL-SLOPE ADC, PQFP44 |
| TC7136CPI | 1-CH DUAL-SLOPE ADC, PDIP40 |
| TC7136CKW713 | 1-CH DUAL-SLOPE ADC, PQFP44 |
| TC7136CKW | 1-CH DUAL-SLOPE ADC, PQFP44 |
| TC7136ACLW | DUAL-SLOPE ADC, PARALLEL ACCESS, PQCC44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC7136ACKW713 | 功能描述:LCD 驱动器 Low Power RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| TC7136ACLW | 功能描述:LCD 驱动器 Low Power RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| TC7136ACLW713 | 功能描述:LCD 驱动器 Low Power RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| TC7136ACPI | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Low Power 3-1/2 Digit Analog-to-Digital Converter |
| TC7136ACPL | 功能描述:LCD 驱动器 Low Power RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。