- 您现在的位置：买卖IC网 > PDF目录66307 > TC71EOA 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 PDF资料下载
参数资料
| 型号： | TC71EOA |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 封装： | SO-8 |
| 文件页数： | 5/9页 |
| 文件大小： | 67K |
| 代理商： | TC71EOA |
5
TC70
TC71
MICROMASTER – SYSTEM
SUPERVISOR WITH POWER SUPPLY
MONITOR, WATCHDOG AND
BATTERY BACKUP
Figure 1. TC70 Typical Application
VCC
CE
WDD
VCCO
CEO
TC70
ADDRESS
DECODER
ADDRESS
CMOS
RAM
I/O
RESET
PROCESSOR
+5V
+3V LI
BATTERY
R2
13K
R1
10K
+5V
VBATT
VCC
GND
CEI
RS
data corruption during power up and power down. The
battery switchover circuit compares VCC to the VBATT input
and connects VCCO to whichever is higher. Switchover
(VSW) occurs when VCC is 10mV below VBATT as VCC falls,
and when VCC is 10mV more than VBATT as VCC rises. The
battery switchover comparator has 20mV of hysteresis to
prevent switch chattering if VCC falls very slowly.
Integrated Battery Backup (TC71)
The TC71 differs from the TC70 in that it has a Power
Fail (PF) output instead of a gated chip enable (CEI, CEO).
PF must be externally gated with the decode for the CMOS
RAM or other device to be battery-backed. (Many CMOS
RAMs have both CE and CE enables. In this case, the PF
output can be connected directly to the CE input of the RAM).
PF is high as long as VCC is greater than 4.5V nominal.
When VCC falls below 4.5V nominal, PF is driven low.
Battery switchover for the TC71 is otherwise identical to that
of the TC70.
Supply Monitor Noise Sensitivity
The TC70/71 is optimized for fast response to negative-
going changes in VDD. Systems with an inordinate amount
of electrical noise on VDD (such as systems using relays),
may require a 0.1
F bypass capacitor to reduce detection
sensitivity. This capacitor should be installed as close to the
TC70/71 as possible to keep the capacitor lead length short.
TYPICAL APPLICATIONS
Figure 1 shows a full feature implementation of the
TC70; Figure 2 shows the TC71. Resistors R1 and R2 of
Figure 2 set the trip point voltage for the early power fail
warning circuit using the TC71 threshold detector.
Resistor Value Selection
The values of R1 and R2 must be chosen to ensure a
valid low strobe level (VSTL) on RS when the processor I/O
line is low. The use of 10k
and 13k, ±5% tolerance
resistors are recommended. These values result in a nomi-
nal strobe level of 2.83V on RS (min/max of 2.43V/3.24V,
assuming VDD = 5.0V ±10%). Other resistor values can be
used, so long as the additive tolerances of the power supply
and resistor values result in a strobe that falls within VSTH
and VSTL under all additive tolerance conditions.
External Override Reset Control
A built-in debounce circuit allows a pushbutton switch
(or other electronic reset signal) to be wire-ORed to RS as
an external reset override (Figure 4). The external reset
signal is required to be an active low signal of at least
20msec in duration. Internally, this input is timed to provide
a minimum reset pulse width output of 500msec.
Threshold Detector
The TC71 issues a low-true output on the TDO pin any
time the TDI pin is less than 1.3V and VCC is greater than
VBATT. The voltage to be monitored is connected to the TDI
input through a simple resistor divider. The threshold detec-
tor can be used to generate an early power fail warning if the
unregulated DC input to the +5V regulator is available for
monitoring.
Integrated Battery Backup (TC70)
The CEO line (TC70) drives the CE input of a CMOS
RAM or other device to be battery-backed. CEO follows CEI
as long as VCC is greater than 4.5V nominal. If VCC falls
below 4.5V nominal, CEO is driven to the potential of VCCO
thus write protecting the RAM and preventing accidental
相关PDF资料 |
PDF描述 |
|---|---|
| TC71COA | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| TC74A0-5.0VAT | SPECIALTY ANALOG CIRCUIT, PSFM5 |
| TC74A1-3.3VCTRT | SPECIALTY ANALOG CIRCUIT, PDSO5 |
| TC74A0-3.3VAT | SPECIALTY ANALOG CIRCUIT, PSFM5 |
| TC74A0-3.3VCTTR | SPECIALTY ANALOG CIRCUIT, PDSO5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC71EPA | 制造商:TELCOM 制造商全称:TelCom Semiconductor, Inc 功能描述:MICROMASTER - SYSTEM SUPERVISOR WITH POWER SUPPLY MONITOR, WATCHDOG AND BATTERY BACKUP |
| TC72 | 功能描述:铝质电解电容器 - 带引线 450V 10UF AXIAL RoHS:否 制造商:Kemet 引线类型: 电容:220 uF 容差:20 % 电压额定值:25 V 工作温度范围: 端接类型:Radial 外壳直径:8 mm 外壳长度:11 mm 引线间隔:5 mm 产品:General Purpose Electrolytic Capacitors 封装:Bulk |
| TC-72.000MBD-T | 功能描述:标准时钟振荡器 72.000MHz 3.3V 25ppm -40C to 85C RoHS:否 制造商:AVX 产品:Standard Clock Oscillators 封装 / 箱体:7 mm x 5 mm 频率:75 MHz 频率稳定性:50 PPM 电源电压:2.5 V 负载电容: 端接类型:SMD/SMT 最小工作温度:0 C 最大工作温度:+ 70 C 输出格式:LVDS 尺寸: 封装:Reel 系列: |
| TC-72.000MBE-T | 制造商:TXC Corporation 功能描述:OSC MEMS 72.000 MHZ 3.3V SMD |
| TC-72.000MCD-T | 功能描述:标准时钟振荡器 72.000MHz 2.5V 25ppm -40C to 85C RoHS:否 制造商:AVX 产品:Standard Clock Oscillators 封装 / 箱体:7 mm x 5 mm 频率:75 MHz 频率稳定性:50 PPM 电源电压:2.5 V 负载电容: 端接类型:SMD/SMT 最小工作温度:0 C 最大工作温度:+ 70 C 输出格式:LVDS 尺寸: 封装:Reel 系列: |
发布紧急采购，3分钟左右您将得到回复。