- 您现在的位置：买卖IC网 > PDF目录69481 > TC74A5-3.3VCT SPECIALTY ANALOG CIRCUIT, PDSO5 PDF资料下载
参数资料
| 型号： | TC74A5-3.3VCT |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO5 |
| 封装： | SOT-23A, 5 PIN |
| 文件页数： | 15/16页 |
| 文件大小： | 430K |
| 代理商： | TC74A5-3.3VCT |
TC74
DS21462B-page 8
2002 Microchip Technology Inc.
FIGURE 3-1:
SMBUS PROTOCOLS
3.3
START Condition (S)
The TC74 continuously monitors the SDA and SCL
lines for a START condition (a HIGH to LOW transition
of SDA while SCL is HIGH) and will not respond until
this condition is met.
3.4
Address Byte
Immediately following the START Condition, the host
must transmit the address byte to the TC74. The states
of A1 and A0 determine the 7-bit SMBus address for
the TC74. The 7-bit address transmitted in the serial bit
stream must match for the TC74 to respond with an
Acknowledge (indicating the TC74 is on the bus and
ready to accept data). The 8-bit in the Address Byte is
a Read/Write Bit. This bit is a ‘1’ for a read operation or
‘0’ for a write operation. During the first phase of any
transfer this bit will be set = 0 to indicate that the
command byte is being written.
3.5
Acknowledge (ACK)
Acknowledge (ACK) provides a positive handshake
between the host and the TC74. The host releases
SDA after transmitting 8 bits. The host then generates
a ninth clock cycle to allow the TC74 to pull the SDA
line LOW. This action acknowledges that the TC74
successfully received the previous eight bits of data or
address.
3.6
Data Byte
After a successful ACK of the address byte, the host
must transmit the data byte to be written or clock in the
data to be read. (See the appropriate timing diagrams).
ACK will be generated after a successful write of a data
byte into the TC74.
3.7
STOP Condition (P)
Communications must be terminated by a STOP
condition (a LOW to HIGH transition of SDA while SCL
is HIGH). The STOP Condition must be communicated
by the transmitter to the TC74. NOTE: Refer to Timing
Diagrams for serial bus timing.
S
Address
WR
ACK
Command
ACK
Data
ACK
P
8 Bits
7 Bits
8 Bits
Slave Address
Command Byte: selects
which register you are
writing to.
Data Byte: data goes
into the register set
by the command byte.
Write Byte Format
Read Byte Format
S Address
WR
ACK
Command
ACK
S
Address
RD ACK
Data
NACK P
7 Bits
8 Bits
7 Bits
8 Bits
Slave Address
Command Byte: selects
which register you are
reading from.
Slave Address: repeated
due to change in data-
flow direction.
Data Byte: reads from
the register set by the
command byte.
Receive Byte Format
S
Address
RD ACK
Data
Nack
P
7 Bits
8 Bits
Data Byte: reads data from
the register commanded by
the last Read Byte or Write
Byte transmission.
S = START Condition
P = STOP Condition
Shaded = Slave Transmission
相关PDF资料 |
PDF描述 |
|---|---|
| TC74A2-5.0VCT | SPECIALTY ANALOG CIRCUIT, PDSO5 |
| TC74A0-5.0VCT | SPECIALTY ANALOG CIRCUIT, PDSO5 |
| TC74HC4052AFT | DUAL 4-CHANNEL, DIFFERENTIAL MULTIPLEXER, PDSO16 |
| TC74HC4052AF | DUAL 4-CHANNEL, DIFFERENTIAL MULTIPLEXER, PDSO16 |
| TC74HC4053AP | TRIPLE 2-CHANNEL, SGL ENDED MULTIPLEXER, PDIP16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC74A5-5.0VAT | 功能描述:板上安装温度传感器 Digital Thermal RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| TC74A5-5.0VAT | 制造商:Microchip Technology Inc 功能描述:Temperature Sensor IC |
| TC74A5-5.0VCT | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Tiny Serial Digital Thermal Sensor |
| TC74A5-5.0VCTTR | 功能描述:板上安装温度传感器 Digital Thermal RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| TC74A5-5.0VCTTRG | 功能描述:板上安装温度传感器 Digital Thermal RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。