- 您现在的位置：买卖IC网 > PDF目录19550 > TC74A7-5.0VAT (Microchip Technology)IC DGTL THERM SNSR 5.0V TO220-5 PDF资料下载
参数资料
| 型号： | TC74A7-5.0VAT |
| 厂商： | Microchip Technology |
| 文件页数： | 6/16页 |
| 文件大小： | 338K |
| 描述： | IC DGTL THERM SNSR 5.0V TO220-5 |
| 标准包装： | 50 |
| 功能： | 温度监控系统（传感器） |
| 传感器类型： | 内部 |
| 感应温度： | -40°C ~ 125°C |
| 精确度： | ±3°C（最小值） |
| 拓扑： | ADC（三角积分型），寄存器库 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 无 |
| 输出风扇： | 无 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 通孔 |
| 封装/外壳： | TO-220-5 |
| 供应商设备封装： | TO-220-5 |
| 包装： | 管件 |
| 其它名称： | TC74A75.0VAT |
TC74
DS21462C-page 6
?2002 Microchip Technology Inc.
3.0
DETAILED DESCRIPTION
3.1
Functional Description
The TC74 acquires and converts temperature
information from its onboard solid-state sensor with a
resolution of ?癈. It stores the data in an internal
register which is then read through the serial port. The
system interface is a slave SMBus/I
2
C port, through
which temperature data can be read at any time. Eight
SMBus/I
2
C addresses are programmable for the TC74,
which allows for a multi-sensor configuration. Also,
there is low power Standby mode when temperature
acquisition is suspended.
3.1.1
STANDBY MODE
The host is allowed, by the TC74, to put it into a low
power (I
DD
= 5 礎, typical) Standby mode. In this
mode, the A/D converter is halted and the temperature
data registers are frozen. The SMBus/I
2
C port, though,
operates normally. Standby mode is enabled by setting
the SHDN bit in the CONFIG register. Table 3-1
summarizes this operation.
TABLE 3-1:
STANDBY MODE OPERATION
3.1.2
SMBUS/I
2
C SLAVE ADDRESS
The TC74 is internally programmed to have a default
SMBus/I
2
C address value of 1001 101b. Seven other
addresses are available by custom order (contact
Microchip Technology Inc.
3.2
Serial Port Operation
The Serial Clock input (SCLK) and bidirectional data
port (SDA) form a 2-wire bidirectional serial port for pro-
gramming and interrogating the TC74. The
conventions used in this bus architecture are listed in
Table 3-2.
TABLE 3-2:
SERIAL BUS CONVENTIONS
All transfers take place under the control of a host, usu-
ally a CPU or microcontroller, acting as the Master. This
host provides the clock signal for all transfers. The
TC74 always operates as a Slave. The serial protocol
is illustrated in Figure 3-1. All data transfers have two
phases and all bytes are transferred MSB first.
Accesses are initiated by a START condition, followed
by a device address byte and one or more data bytes.
The device address byte includes a Read/Write selec-
tion bit. Each access must be terminated by a STOP
condition. A convention called Acknowledge (ACK)
confirms receipt of each byte. Note that SDA can
change only during periods when SCLK is low (SDA
changes while SCLK is high are reserved for START
and STOP conditions).
SHDN Bit
Operating Mode
0
Normal
1
Standby
Term
Explanation
Transmitter The device sending data to the bus.
Receiver
The device receiving data from the bus.
Master
The device which controls the bus initi-
ating transfers (START), generating the
clock and terminating transfers
(STOP).
Slave
The device addressed by the master.
START
A unique condition signaling the begin-
ning of a transfer indicated by SDA
falling (high-low) while SCLK is high.
STOP
A unique condition signaling the end of
a transfer indicated by SDA rising (low-
high) while SCLK is high.
ACK
A Receiver acknowledges the receipt
of each byte with this unique condition.
The Receiver drives SDA low during
SCLK high of the ACK clock-pulse. The
Master provides the clock pulse for the
ACK cycle.
Busy
Communication is not possible
because the bus is in use.
NOT Busy When the bus is idle, both SDA and
SCLK will remain high.
Data Valid The state of SDA must remain stable
during the high period of SCLK in order
for a data bit to be considered valid.
SDA only changes state while SCLK is
low during normal data transfers (see
START and STOP conditions).
相关PDF资料 |
PDF描述 |
|---|---|
| VI-BTZ-CY-F1 | CONVERTER MOD DC/DC 2V 20W |
| TC74A2-5.0VAT | IC DGTL THERM SNSR 5.0V TO220-5 |
| RW2-243.3D | CONV DC/DC 2W 18-36VIN +/-3.3V |
| VI-2V0-CY-F3 | CONVERTER MOD DC/DC 5V 50W |
| A331M15X7RL5UAA | CAP CER 330PF 500V 20% X7R AXIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC74A7-50VCT | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Tiny Serial Digital Thermal Sensor |
| TC74AC00F | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:QUAD 2 - INPUT NAND GATE |
| TC74AC00F(F) | 制造商:Toshiba 功能描述:74AC Quad 2-Input NAND Gate 14SOP Bulk 制造商:Toshiba America Electronic Components 功能描述:IC, 74 series logic 制造商:Toshiba 功能描述:NAND Gate 4-Element 2-IN CMOS 14-Pin SOP Tube |
| TC74AC00F_12 | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:Quad 2-Input NAND Gate |
| TC74AC00FN | 功能描述:IC GATE NAND QUAD 2INP 14-SOL RoHS:否 类别:集成电路 (IC) >> 逻辑 - 栅极和逆变器 系列:74AC 标准包装:2,000 系列:74LCX 逻辑类型:逆变器，缓冲器 电路数:1 输入数:8 特点:三态 电源电压:2 V ~ 3.6 V 电流 - 静态（最大值）:10µA 输出电流高，低:24mA，24mA 逻辑电平 - 低:0.7 V ~ 0.8 V 逻辑电平 - 高:1.7 V ~ 2 V 额定电压和最大 CL 时的最大传播延迟:6.5ns @ 3.3V，50pF 工作温度:-40°C ~ 85°C 安装类型:表面贴装 供应商设备封装:20-SSOP 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。