参数资料
| 型号： | TC7652CPD |
| 厂商： | Microchip Technology |
| 文件页数： | 15/16页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP CHOPPER STAB LN 14DIP |
| 标准包装： | 30 |
| 放大器类型： | 断路器（零漂移） |
| 电路数： | 1 |
| 转换速率： | 1 V/µs |
| 增益带宽积： | 400kHz |
| 电流 - 输入偏压： | 30pA |
| 电压 - 输入偏移： | 2000µV |
| 电流 - 电源： | 1mA |
| 电压 - 电源，单路/双路(±)： | 5 V ~ 16 V，±2.5 V ~ 8 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 14-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 14-PDIP |
| 包装： | 管件 |
| 其它名称： | 158-1024 158-1024-ND |
TC7652
DS21464B-page 8
2002 Microchip Technology Inc.
4.6
Pin Compatibility
Where possible, the 8-pin device pinout conforms to
such industry standards as the LM101 and LM741. Null
storing external capacitors connect to Pins 1 and 8,
which are usually for offset null or compensation capac-
itors. Output clamp (Pin 5) is similarly used. For OP05
and OP07 devices, replacement of the offset null
potentiometer (connected between Pins 1 and 8 and
VDD by two capacitors from those pins to VSS) provides
compatibility. Replacing the compensation capacitor
between Pins 1 and 8 by two capacitors to VSS is
required. The same operation (with the removal of any
connection to Pin 5) works for LM101,
A748 and sim-
ilar parts.
Because NC pins provide guarding between input and
other pins, the 14-pin device pinout conforms closely to
the LM108. Because this device does not use any extra
pins and does not provide offset nulling (but requires a
compensation capacitor), some layout changes are
necessary to convert to the TC7652.
4.7
Some Applications
Figures 4-2 and 4-3 show basic inverting and nonin-
verting amplifier circuits using the output clamping cir-
cuit to enhance overload recovery performance. The
only limitations on replacing other op amps with the
TC7652 are supply voltage (±8V maximum) and output
drive capability (10k
load for full swing). Overcome
these limitations with a booster circuit (Figure 4-4) to
combine output capabilities of the LM741 (or other
standard device) with input capabilities of the TC7652.
These two form a composite device, therefore, when
adding the feedback network, the monitor loop gains
stability.
FIGURE 4-2:
NONINVERTING
AMPLIFIER WITH
OPTIONAL CLAMP
FIGURE 4-3:
INVERTING AMPLIFIER
WITH OPTIONAL CLAMP
FIGURE 4-4:
USING 741 TO BOOST
OUTPUT DRIVE
CAPABILITY
Figure 4-5 shows the clamp circuit of a zero offset com-
parator. Because the clamp circuit requires the invert-
ing input to follow the input signal, problems with a
chopper stabilized op amp are avoided. The threshold
input must tolerate the output clamp current
≈VIN/R
without disrupting other parts of the system.
Figure 4-6 shows how the TC7652 can offset null high
slew rate and wideband amplifiers.
Mixing the TC7652 with circuits operating at ±15V
requires a lower supply voltage divider with the TC7660
voltage converter circuit operated "backwards." Figure
4-7 shows an approximate connection.
FIGURE 4-5:
LOW OFFSET
COMPARATOR
TC7652
+
–
Output
Clamp
Input
0.1F
R2
R1
R3
0.1F
+
–
Output
Input
R2
R1
Clamp
0.1F
TC7652
+
–
+
–
+15V
-15V
-7.5V
0.1
F
In
Out
-7.5V
0.1
F
10k
TC7652
741
TC7652
+
–
VOUT
Clamp
VIN
0.1F
200k
to 2m
VTH
相关PDF资料 |
PDF描述 |
|---|---|
| TC913ACPA | IC OPAMP DUAL AUTO ZERO 8DIP |
| TCA0372DWG | IC OPAMP DUAL POWER 1A 16SOIC |
| TDA1348AE | 48V FAN 127X127X38MM |
| TDA1548AG | 48V FAN 172X150X50.8MM |
| TDA1748AG | 48V FAN 172X50.8MM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC7652IJA | 功能描述:运算放大器 - 运放 Low Noise RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| TC7652IJD | 功能描述:运算放大器 - 运放 Low Noise RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| TC7660 | 制造商:MICRO CHIP 功能描述: |
| TC7660_02 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Charge Pump DC-to-DC Voltage Converter |
| TC7660CJA | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Charge Pump DC-to-DC Voltage Converter |
发布紧急采购，3分钟左右您将得到回复。