- 您现在的位置：买卖IC网 > PDF目录98181 > TC820CKW 1-CH DUAL-SLOPE ADC, PQFP44 PDF资料下载
参数资料
| 型号： | TC820CKW |
| 元件分类： | ADC |
| 英文描述： | 1-CH DUAL-SLOPE ADC, PQFP44 |
| 封装： | PLASTIC, QFP-44 |
| 文件页数： | 14/28页 |
| 文件大小： | 616K |
| 代理商： | TC820CKW |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
2002 Microchip Technology Inc.
DS21476B-page 21
TC820
5.11
External Peak Detection
The TC820 will hold the highest A/D conversion or fre-
quency reading indefinitely when the PKHOLD input is
connected to VDD. However, the analog peak input
must be present during the A/D converter's signal inte-
grate period. For slowly changing signals, such as tem-
perature, the peak reading will be properly converted
and held.
If rapidly changing analog signals must be held, an
external peak detector should be added. An inexpensive
circuit can be made from an op amp and a few discrete
components, as shown in Figure 5-12. The droop rate of
the external peak detector should be adjusted so that the
held voltage will not decay below the desired accuracy
level during the converter's 400msec conversion time.
FIGURE 5-12:
EXTERNAL PEAK
DETECTOR
5.12
Liquid Crystal Display (LCD)
The TC820 drives a triplex (multiplexed 3:1) LCD with
three backplanes. The LCD can include decimal points,
polarity sign, and annunciators for over range, peak
hold, high and low logic levels, and low battery.
Table 5-2 shows the assignment of the display seg-
ments to the backplanes and segment drive lines. The
backplane drive frequency is obtained by dividing the
oscillator frequency by 240.
Backplane waveforms are shown in Figure 5-13. These
appear on outputs BP1, BP2, and BP3. They remain the
same, regardless of the segments being driven.
FIGURE 5-13:
BACKPLANE
WAVEFORMS
Other display output lines have waveforms that vary
depending on the displays values. Figure 5-13 shows a
set of waveforms for the a, g, d outputs of one digit for
several combinations of "on" segments.
FIGURE 5-14:
TYPICAL DISPLAY
OUTPUT WAVEFORMS
TABLE 5-2:
LCD BACKPLANE AND
SEGMENT ASSIGNMENTS
*Connect both pins 2 and 16 of LCD to TC820 BP3 of output.
VDD
TC820
+
–
VSS
VIN+
PKHOLD
0V
0.01F
Offset Null
1N4148
+9V
10k
VIN
TL061
BP1
BP2
BP3
40-Pin
(PDIP)
44-Pin
(PQFP)
LCD Display
Pin Number
BP1
BP2
BP3
140
3
LOW
241
4
A4
"—"
3
42
5
B4
G4
E4
4
43
6
HIGH
C4
D4
544
7
A3
F3
DP3
61
8
B3
G3
E3
7
2
9
OVER
C3
D3
83
10
A2
F2
DP2
9
4
11
B2
G2
E2
10
5
12
PEAK
C2
D2
11
6
13
A1
F1
DP1
12
7
14
B1
G1
E1
13
8
2,16*
—
C1
D1
14
9
1
BP1
—
BATT
15
10
15
LOW
BP2
BP3
VDD
VH
VL
VDISP
VDD
VH
VL
VDISP
VDD
VH
VL
VDISP
VDD
VH
VL
VDISP
Segment
Line
All OFF
a Segment
ON
d, g OFF
a, g ON
d OFF
All ON
相关PDF资料 |
PDF描述 |
|---|---|
| TC820CLW | 1-CH DUAL-SLOPE ADC, PQCC44 |
| TC820CPL | 1-CH DUAL-SLOPE ADC, PDIP40 |
| TC820CLW | DUAL-SLOPE ADC, PARALLEL ACCESS, PQCC44 |
| TC820CPL | DUAL-SLOPE ADC, PARALLEL ACCESS, PDIP40 |
| TC821CKW | CONVERTER SUBSYSTEM ADC, PARALLEL ACCESS, PQFP44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC820CKW713 | 功能描述:LCD 驱动器 3-3/4 A/D Converter RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| TC820CLW | 功能描述:LCD 驱动器 3-3/4 A/D Converter RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| TC820CLW713 | 功能描述:LCD 驱动器 3-3/4 A/D Converter RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| TC820CPL | 功能描述:LCD 驱动器 3-3/4 A/D Converter RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| TC8-20S2405R | 制造商:TRUMPOWER 制造商全称:Tumbler Technologies + TRUMPower 功能描述:DC/DC CONVERTERS 2:1 Input, 12.5 to 20 Watt |
发布紧急采购，3分钟左右您将得到回复。