- 您现在的位置：买卖IC网 > PDF目录98183 > TC9028F INFRARED, TRANSMITTER IC, PDSO20 PDF资料下载
参数资料
| 型号： | TC9028F |
| 元件分类： | 摇控器 |
| 英文描述： | INFRARED, TRANSMITTER IC, PDSO20 |
| 封装： | 0.300 INCH, 1.27 MM PITCH, PLASTIC, SOP-20 |
| 文件页数： | 5/21页 |
| 文件大小： | 571K |
| 代理商： | TC9028F |
TC9028P/F
2002-01-08
13
4.1.1
Hold mode
Hold mode is activated by executing the hold instruction [HOLD]. Hold mode continues as long as
the HCAN pins are at low level.
The following states are held during hold mode.
(1) Oscillation stops and all internal operations stop.
(2) The timer counter is cleared to 0.
(3) Data memory, registers, and port latches hold the states immediately before entering hold
mode. (Note that the status flag is set to 1.)
(4) The program counter holds the 2 addresses after the hold instruction.
(After hold mode is cancelled, execution resumes with the instruction following the hold
instruction.)
4.1.2
Hold mode cancellation
Hold mode is cancelled and normal operation resumes when high level is input to the HCAN pins
during hold mode.
Hold mode is cancelled in the following sequence.
(1) Oscillation begins.
(2) Warming-up for the time required to stabilize oscillation. Internal operation remains stopped
during warming-up.
The warming-up time is 211/fc (s).
(3) After the warming-up time has elapsed, normal operation resumes from the instruction
following the hold instruction.
Note 2: The fundamental clock is divided by the interval timer. If the oscillation frequency fluctuates
after hold mode is cancelled, the warming-up time is not exactly the same as the value given
above. Thus, the warming-up time has allowance.
Hold mode is also cancelled by setting the RST pin to low level. In this case, the reset operation
is performed immediately. Since normal operation begins at the same time the reset operation is
cancelled, the RST pin must be kept at the low level for the warming-up time until oscillation
becomes stable.
If input to the HCAN pin is at high level, executing the hold instruction does not enter hold mode
but instead moves immediately to the cancellation sequence (warming-up). The warming-up time
in this case is an undefined value between 0~211/fc (s). Therefore, when the hold instruction is
executed, input to the HCAN pin must be set to low level.
相关PDF资料 |
PDF描述 |
|---|---|
| TC9083N | PICTURE-IN-PICTURE IC, PDIP42 |
| TC9090AN | Y/C SEPARATOR IC, PDIP28 |
| TC9090AF | Y/C SEPARATOR IC, PDSO28 |
| TC90A11F | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
| TC90A13N | Y/C SEPARATOR IC, PDIP28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC9028P | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:INFRARED REMOTE CONTROL TRANSMITTING CMOS LSI WITH MICROCONTROLLING |
| TC9-02-AG | 制造商:TE Connectivity 功能描述:Accessories (Terminal Block) |
| TC9-03-AG | 功能描述:接线端子工具和配件 TC9-03-AG=721011400 RoHS:否 制造商:Phoenix Contact 产品:Tools & Accessories 类型:End Bracket |
| TC9-04-AG | 功能描述:接线端子工具和配件 TC9-04-AG=721046000 RoHS:否 制造商:Phoenix Contact 产品:Tools & Accessories 类型:End Bracket |
| TC90517FG(BS,DRY) | 制造商:Toshiba America Electronic Components 功能描述:OFDM DEMODULATOR (CHANNEL DECODER ICS) - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。