- 您现在的位置：买卖IC网 > PDF目录69482 > TCA3727G (INFINEON TECHNOLOGIES AG) STEPPER MOTOR CONTROLLER, 1 A, PDSO24 PDF资料下载
参数资料
| 型号： | TCA3727G |
| 厂商： | INFINEON TECHNOLOGIES AG |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 1 A, PDSO24 |
| 封装： | PLASTIC, DSO-24 |
| 文件页数： | 17/29页 |
| 文件大小： | 604K |
| 代理商： | TCA3727G |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
TCA 3727
Data Sheet
24
Rev. 2.0, 2004-10-01
Application Hints
The TCA 3727 is intended to drive both phases of a stepper motor. Special care has
been taken to provide high efficiency, robustness and to minimize external components.
Power Supply
The TCA 3727 will work with supply voltages ranging from 5 V to 50 V at pin
V
S. As the
circuit operates with chopper regulation of the current, interference generation problems
can arise in some applications. Therefore the power supply should be decoupled by a
0.22
F ceramic capacitor located near the package. Unstabilized supplies may even
afford higher capacities.
Current Sensing
The current in the windings of the stepper motor is sensed by the voltage drop across
R
1
and
R
2. Depending on the selected current internal comparators will turn off the sink
transistor as soon as the voltage drop reaches certain thresholds (typical 0 V, 0.25 V,
0.5 V and 0.75 V); (
R
1, R2 = 1 ). These thresholds are neither affected by variations of
V
L nor by variations of VS.
Due to chopper control fast current rises (up to 10 A/
s) will occur at the sensing
resistors
R
1 and R2. To prevent malfunction of the current sensing mechanism R1 and R2
should be pure ohmic. The resistors should be wired to GND as directly as possible.
Capacitive loads such as long cables (with high wire to wire capacity) to the motor should
be avoided for the same reason.
Synchronizing Several Choppers
In some applications synchronous chopping of several stepper motor drivers may be
desirable to reduce acoustic interference. This can be done by forcing the oscillator of
the TCA 3727 by a pulse generator overdriving the oscillator loading currents
(approximately
≥ ±100 A). In these applications low level should be between 0 V and
1 V while high level should be between 2.6 V and
V
L.
Optimizing Noise Immunity
Unused inputs should always be wired to proper voltage levels in order to obtain highest
possible noise immunity.
To prevent crossconduction of the output stages the TCA 3727 uses a special break
before make timing of the power transistors. This timing circuit can be triggered by short
glitches (some hundred nanoseconds) at the Phase inputs causing the output stage to
become high resistive during some microseconds. This will lead to a fast current decay
during that time. To achieve maximum current accuracy such glitches at the Phase
inputs should be avoided by proper control signals.
相关PDF资料 |
PDF描述 |
|---|---|
| TCA3727 | STEPPER MOTOR CONTROLLER, 1 A, PDIP20 |
| TCD2502C-1 | SPECIALTY ANALOG CIRCUIT, CDIP24 |
| TCD2554D | SPECIALTY ANALOG CIRCUIT, CDIP24 |
| TCD2556D | SPECIALTY ANALOG CIRCUIT, CDIP22 |
| TCD2953CF | SPECIALTY ANALOG CIRCUIT, CDMA32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TCA3727GNT | 制造商:Infineon Technologies AG 功能描述:2-Phase Stepping Motor Driver 24-Pin DSO T/R |
| TCA3727GXT | 制造商:Infineon Technologies AG 功能描述:2-Phase Stepping Motor Driver 24-Pin DSO |
| TCA3727GXUMA1 | 制造商:Infineon Technologies AG 功能描述:2-Phase Stepping Motor Driver 24-Pin DSO 制造商:Infineon Technologies AG 功能描述:BODY BRIDGES - Tape and Reel 制造商:Infineon Technologies AG 功能描述:IC MOTOR DRIVER PAR 24DSO |
| TCA3727NKLA1 | 制造商:Infineon Technologies AG 功能描述:2-Phase Stepping Motor Driver 20-Pin PDIP 制造商:Infineon Technologies AG 功能描述:IC MOTOR DRIVER PAR 20DIP |
| TCA3737G | 制造商:Infineon Technologies AG 功能描述: |
发布紧急采购，3分钟左右您将得到回复。