- 您现在的位置：买卖IC网 > PDF目录98186 > TCM320AC46N (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PDIP20 PDF资料下载
参数资料
| 型号： | TCM320AC46N |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDIP20 |
| 文件页数： | 14/19页 |
| 文件大小： | 246K |
| 代理商： | TCM320AC46N |
TCM320AC46
GENERAL-PURPOSE AUDIO INTERFACE FOR DSP
SLWS001 – D4091, JUNE 1993
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
4
general information
system reliability features
The device should be powered up and initialized as follows:
1.
GND is applied.
2.
VCC is applied.
3.
All clocks are connected.
4.
TTL high is applied to PDN.
5.
FSX and/or FSR synchronization pulses are applied.
Even though the device is heavily protected against latch-up, it is still possible to cause it to latch-up under
certain improper power conditions where excess current is forced into or out of one or more terminals. To assure
that latch-up will not occur, it is good design practice to put a reverse-biased Schottky diode between VCC (power
supply) and GND.
On the transmit channel, digital outputs DOUT and TSX are held in the high-impedance state for approximately
four frames (500
s) after power up or application of VCC. After this delay, DOUT, TSX, and signaling are
functional and occur in the proper time slot. The analog circuits on the transmit side require approximately 60
ms to reach their equilibrium value due to the autozero circuit settling time. To further enhance system integrity,
DOUT and TSX are placed in the high-impedance state after an interruption of CLK.
power-down and standby operations
To minimize power consumption, a power-down mode and three standby modes are provided.
For power down, an external low signal is applied to PDN. In the absence of a signal, PDN is internally pulled
up to a high logic level and the device remains active. In the power-down mode, the average power consumption
is reduced to 3 mW.
The standby modes give the user the options of putting the entire device on standby, putting only the transmit
channel on standby, or putting only the receive channel on standby. To place the entire device on standby, both
FSX and FSR are held low. For transmit-only operation, FSX is pulsed and FSR is held low. For receive-only
operation, FSR is pulsed and FSX is held low. In the standby mode with both transmit and receive on standby,
power consumption is reduced to 8 mW. See Table 1 for power-down and standby procedures.
相关PDF资料 |
PDF描述 |
|---|---|
| TCM320AC46DW | SPECIALTY CONSUMER CIRCUIT, PDSO20 |
| TCM5030T | SPECIALTY ANALOG CIRCUIT, CQCC32 |
| TCM5033T | SPECIALTY ANALOG CIRCUIT, CQCC32 |
| TCM8240MD | SPECIALTY ANALOG CIRCUIT |
| TCT101A | 1 FUNCTIONS, 300 V, 10 A, FEED THROUGH CAPACITOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TCM320AC54 | 制造商:TI 制造商全称:Texas Instruments 功能描述:MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER |
| TCM320AC54CDW | 制造商:Texas Instruments 功能描述: |
| TCM320AC54CN | 制造商:Texas Instruments 功能描述: |
| TCM320AC54DW | 制造商:TI 制造商全称:Texas Instruments 功能描述:MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER |
| TCM320AC54N | 制造商:TI 制造商全称:Texas Instruments 功能描述:MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER |
发布紧急采购，3分钟左右您将得到回复。