- 您现在的位置：买卖IC网 > PDF目录66309 > TCM810RENBTR 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 PDF资料下载
参数资料
| 型号： | TCM810RENBTR |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| 封装： | TO-236, SOT-23B, 3 PIN |
| 文件页数： | 3/8页 |
| 文件大小： | 53K |
| 代理商： | TCM810RENBTR |
3
TCM809/810-01
1/22/01
TCM809
TCM810
3-Pin Microprocessor Reset Monitors
2001 Microchip Technology Inc.
DS21602A
TCM809
VCC
R1
100k
RESET
GND
Combinations above the curve are detected as a brown-
out or power-down. Transient immunity can be improved by
adding a capacitor in close proximity to the VCC pin of the
TCM809/810.
RESET Signal Integrity During Power-Down
The TCM809 RESET output is valid to VCC = 1.0V.
Below this voltage the output becomes an "open circuit" and
does not sink current. This means CMOS logic inputs to the
P will be floating at an undetermined voltage. Most digital
systems are completely shutdown well above this voltage.
However, in situations where RESET must be maintained
valid to VCC = 0V, a pull-down resistor must be connected
from RESET to ground to discharge stray capacitances and
hold the output low (Figure 2). This resistor value, though not
critical, should be chosen such that it does not appreciably
load RESET under normal operation (100k
will be suitable
for most applications). Similarly, a pull-up resistor to VCC is
required for the TCM810 to ensure a valid high RESET for
VCC below 1.0V.
APPLICATIONS INFORMATION
VCC Transient Rejection
The TCM809/810 provides accurate VCC monitoring
and reset timing during power-up, power-down, and brown-
out/sag conditions, and rejects negative-going transients
(glitches) on the power supply line. Figure 1 shows the
maximum transient duration vs. maximum negative excur-
sion (overdrive) for glitch rejection. Any combination of
duration and overdrive which lies under the curve will not
generate a reset signal.
PIN DESCRIPTION
Pin No.
Symbol
Description
1
GND
Ground
2
RESET (TCM809)
RESET output remains low while VCC is below the reset voltage threshold, and
for 240msec (140msec min.) after VCC rises above reset threshold.
2
RESET (TCM810)
RESET output remains high while VCC is below the reset voltage threshold,
and for 240msec (140msec min.) after VCC rises above reset threshold.
3VCC
Supply voltage (+2.5V, +3.0V, +3.3V, +5.0V)
Figure 2. Ensuring RESET Valid to VCC = 0V
Figure 1. Maximum Transient Duration vs.
Overdrive for Glitch Rejection at 25
°C
RESET COMPARATOR OVERDRIVE,
[V
TH - VCC](mV)
400
240
160
320
80
0
1
5
100
1000
MAXIMUM
TRANSIENT
DURATION
(
sec)
TA = +25°C
VTH
Duration
Overdrive
VCC
TCM8XXL/M/J
TCM8XXZ/R/S/T
相关PDF资料 |
PDF描述 |
|---|---|
| TCM809SVNBTR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| TCM810TENBTR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| TCM809SENBTR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| TCM810LENBTR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| TCM809MVNBTR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TCM810RVB713 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:3-Pin Microcontroller Reset Monitors |
| TCM810RVLB713 | 功能描述:监控电路 Microprocessor 2.63V RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| TCM810RVN | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:3-Pin Microcontroller Reset Monitors |
| TCM810RVNB713 | 功能描述:监控电路 Microprocessor 2.63V RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| TCM810SEB713 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:3-Pin Microcontroller Reset Monitors |
发布紧急采购，3分钟左右您将得到回复。