- 您现在的位置：买卖IC网 > PDF目录16522 > TCM810SVLB713 (Microchip Technology)IC RESET MONITOR 2.93V SC70-3 PDF资料下载
参数资料
| 型号： | TCM810SVLB713 |
| 厂商： | Microchip Technology |
| 文件页数： | 5/16页 |
| 文件大小： | 0K |
| 描述： | IC RESET MONITOR 2.93V SC70-3 |
| 标准包装： | 1 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 推挽式，图腾柱 |
| 复位： | 高有效 |
| 复位超时： | 最小为 140 ms |
| 电压 - 阀值： | 2.93V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-70，SOT-323 |
| 供应商设备封装： | SC-70-3 |
| 包装： | 标准包装 |
| 产品目录页面： | 662 (CN2011-ZH PDF) |
| 其它名称： | TCM810SVLB713DKR |
TCM809/TCM810
4.0
4.1
APPLICATIONS INFORMATION
V DD Transient Rejection
Combinations above the curve are detected as a
brown-out or power-down condition. Transient
immunity can be improved by adding a capacitor in
close proximity to the V DD pin of the TCM809/TCM810.
The TCM809/TCM810 provides accurate V DD monitor-
ing and reset timing during power-up, power-down and
4.2
RESET Signal Integrity During
brown-out/sag conditions. These devices also reject
negative-going transients (glitches) on the power
supply line. Figure 4-1 shows the maximum transient
duration vs. maximum negative excursion (overdrive)
for glitch rejection. Any combination of duration and
overdrive that lies under the curve will not generate a
reset signal.
V DD
V TH
Overdrive
Duration
Power-Down
The TCM809 RESET output is valid to V DD = 1.0V.
Below this voltage the output becomes an "open cir-
cuit" and does not sink current. This means CMOS
logic inputs to the microcontroller will be floating at an
undetermined voltage. Most digital systems are
completely shut down well above this voltage.
However, in situations where RESET must be main-
tained valid to V D D = 0V , a pull-down resistor must be
connected from RESET to ground to discharge stray
capacitances and hold the output low (Figure 4-2). This
resistor value, though not critical, should be chosen
such that it does not appreciably load RESET under
normal operation (100 k Ω will be suitable for most
400
320
240
160
80
T A = +25°C
T CM8XX L/M/J (SOT-23)
applications). Similarly, a pull-up resistor to V DD is
required for the TCM810 to ensure a valid high RESET
for V DD below 1.0V.
V DD
V DD
TCM809
0
TCM8XX Z/R/S/T
(SOT-23)
1 5
100
1000
RESET
130
120
Reset Comparator Overdrive
[V TH – V DD ] (mv)
GND
R 1
100 k Ω
110
TCM8XX L/M/J (SC-70)
FIGURE 4-2:
The addition of R 1 at the
100
90
80
70
60
50
40
30
TCM8XX Z/R/S/T (SC-70)
RESET output of the TCM809 ensures that the
RESET output is valid to V DD = 0V.
1
10
100
1000
Reset Comparator Overdrive (mV)
[V TH – V DD ] (mv)
FIGURE 4-1:
Maximum Transient
Duration vs. Overdrive for Glitch Rejection at
+25°C.
? 2005 Microchip Technology Inc.
DS21661D-page 5
相关PDF资料 |
PDF描述 |
|---|---|
| 5492021-2 | CA SM LDD SCDUPLEX(NG)6FT |
| UPA1A561MPD1TD | CAP ALUM 560UF 10V 20% RADIAL |
| 6374656-1 | C/A LC TO LC MM 2.0MM 1M |
| EBM28DTBD-S189 | CONN EDGECARD 56POS R/A .156 SLD |
| 6374612-1 | C/A 50/125 MM SC-LC 1M |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TCM810SVN | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:3-Pin Microcontroller Reset Monitors |
| TCM810SVNB713 | 功能描述:监控电路 Microprocessor 2.93V RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| TCM810TEB713 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:3-Pin Microcontroller Reset Monitors |
| TCM810TELB713 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:3-Pin Microcontroller Reset Monitors |
| TCM810TEN | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:3-Pin Microcontroller Reset Monitors |
发布紧急采购，3分钟左右您将得到回复。