- 您现在的位置：买卖IC网 > PDF目录69485 > TD230IDT (STMICROELECTRONICS) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 PDF资料下载
参数资料
| 型号： | TD230IDT |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| 封装： | MICRO, PLASTIC, SO-16 |
| 文件页数： | 12/15页 |
| 文件大小： | 497K |
| 代理商： | TD230IDT |
6/15
Do
no
t u
se
for
new
design
INTRODUCTION
Over current and short circuit protection is a con-
stant concern for today’s engineers. More and
more applications in different segments (Telecom,
Automotive, Industrial, Computer...) require al-
ways improved reliability after delivery : mainte-
nance costs are an ever more worrying source of
expenses and customers’ dissatisfaction.
Alternatives for short circuit or over current protec-
tions are the fuses and the PTC (Positive Temper-
ature Coefficient) resistors. The first are a cheap
but destructive solution ; the second are tied to a
time constant due to self heating which is often in-
compatible with the host equipment’s require-
ments.
In both cases, a coil can be added for an efficient
limitation of current surges, to the detriment of
weight and volume.
None of these solutions is fully satisfactory for a
reliable, immediate and non destructible short cir-
cuit and over current protection.
1. ELECTRONIC CIRCUIT BREAKER
The electronic circuit breaker TD230 is the conve-
nient solution for any industrial who wants at the
same time :
u immediate, efficient and resettable protec-
tion for his equipment
u versatility regarding different applications
u easy and quick design-in
u low component count
u low cost
The electronic circuit breaker TD230 is to be used
with a minimal amount of external and low cost
components to drive one or two N-channel MOS-
FETs (in respectively single or dual supply appli-
cations) used as power switches between the DC
power supplies and the equipments to be
protected.
The TD230 immediately reacts (3
s max. without
load) whenever an over current is detected by
switching off the corresponding MOSFET. Several
automatic restart attempts are made unless the
fault persists over an externally adjustable amount
of time after which the power MOSFET is defini-
tively switched off, waiting for a reset.
If the fault is detected on the positive supply, the
definitive shutdown will also disconnect the nega-
tive power supply and set a warning low level on
the Shutdown pin. If the fault is detected on the
negative supply, the definitive shutdown will dis-
connect only the negative power supply, and let
the positive part of the circuit undisturbed.
The whole system can be reset in three ways :
u by switching off the power supplies
u by unplugging and re-plugging the card
(live insertion)
u by setting the INHIBIT pin active during a
short time (allowing remote reset)
2. HOW TO USE THE TD230 ?
The typical configuration of the TD230 - Electronic
Circuit Breaker - in a dual supply topology is
shown in figure 1.
In this configuration, both NMOS 1/2 are used as
power switches which connect the equipments to
the power supplies, thus ensuring low voltage
drop through the ON-resistances (Rdson) of
NMOS
1/2.
2.1. Current Limitation
When an over current condition (I
OC) is detected
through the low ohmic shunt resistors RS 1/2 as giv-
en under equation (i) :
u V
RS 1/2 = IOC x RS > 63mV typ. (i)
the gate of the corresponding MOSFET 1/2 is dis-
charged immediately, thus disconnecting the
board/equipment from the power supply.
Note that the over current condition is given by the
constant product I
OC x RS = 63mV, which means
that the IOC limit is directly given by the choice of
the shunt resistors R
S1/2 values.
The TD230 automatically makes restart attempts
by slowly recharging the gate of the MOSFET 1/2
with a 15
A typ. current source ensuring thus slow
ramp with the typical time constant before recon-
duction shown in equation (ii) :
u t
ON = CISS x VTH / 15A (ii)
where CISS is the input capacitance of the power
MOSFET
1/2 and VTH, the threshold voltage of the
MOSFET (typically 5V).
This reconduction time can be extended with an
external soft start capacitor C
SS1/2 as shown in
APPLICATION NOTE
ELECTRONIC CIRCUIT BREAKER
by R. LIOU
相关PDF资料 |
PDF描述 |
|---|---|
| TD62650FG | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO30 |
| TD62652FG | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO30 |
| TDA16832G | 2.7 A SWITCHING REGULATOR, 110 kHz SWITCHING FREQ-MAX, PDSO14 |
| TDA16833G | 4.8 A SWITCHING REGULATOR, 110 kHz SWITCHING FREQ-MAX, PDSO14 |
| TDA16831 | 1.4 A SWITCHING REGULATOR, 110 kHz SWITCHING FREQ-MAX, PDIP8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TD230IN | 功能描述:电源开关 IC - 配电 Circuit Breaker RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| TD230N | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:ELECTRONIC CIRCUIT BREAKER |
| TD231 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Technical Specifications for 5 kA, Normal-Duty Distribution 4.5 kV and 5 kV VariSTAR?? MOV Disks |
| TD231-1000P | 制造商:TE Connectivity 功能描述:TIME DELAY RELAY - Trays |
| TD231-1000S | 制造商:TE Connectivity 功能描述:TIME DELAY RELAY - Trays |
发布紧急采购，3分钟左右您将得到回复。