- 您现在的位置：买卖IC网 > PDF目录98191 > TDA5140AT-T (NXP SEMICONDUCTORS) BRUSHLESS DC MOTOR CONTROLLER, 1 A, PDSO20 PDF资料下载
参数资料
| 型号： | TDA5140AT-T |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 1 A, PDSO20 |
| 封装： | PLASTIC, SOT-163A, SOL-20 |
| 文件页数： | 5/24页 |
| 文件大小： | 174K |
| 代理商： | TDA5140AT-T |
April 1994
13
Philips Semiconductors
Product specication
Brushless DC motor drive circuit
TDA5140A
Fig.8 CAP-CD and CAP-DC typical voltage waveforms in normal running mode.
THE TIMING CAPACITOR (CAP-TI)
Capacitor CAP-TI is used for timing the successive steps
within one commutation period; these steps include some
internal delays.
The most important function is the watchdog time in which
the motor EMF has to recover from a negative diode-pulse
back to a positive EMF voltage (or vice versa). A watchdog
timer is a guarding function that only becomes active when
the expected event does not occur within a predetermined
time.
The EMF usually recovers within a short time if the motor
is running normally (
<<ms). However, if the motor is
motionless or rotating in the reverse direction, then the
time can be longer (
>>ms).
A watchdog time must be chosen so that it is long enough
for a motor without EMF (still) and eddy currents that may
stretch the voltage in a motor winding; however, it must be
short enough to detect reverse rotation. If the watchdog
time is made too long, then the motor may run in the wrong
direction (with little torque).
The capacitor is charged, with a current of 57
A, from
0.2 to 0.3 V. Above this level it is charged, with a current of
5
A, up to 2.2 V only if the selected motor EMF remains
in the wrong polarity (watchdog function). At the end, or, if
the motor voltage becomes positive, the capacitor is
discharged with a current of 28
A. The watchdog time is
the time taken to charge the capacitor, with a current of
5
A, from 0.3 to 2.2 V.
To ensure that the internal delays are covered CAP-TI
must have a minimum value of 2 nF. For the watchdog
function a value for CAP-TI of 10 nF is recommended.
To ensure a good start-up and commutation, care must be
taken that no oscillations occur at the trailing edge of the
flyback pulse. Snubber networks at the outputs should be
critically damped.
Typical voltage waveforms are illustrated by Fig.9.
相关PDF资料 |
PDF描述 |
|---|---|
| TDA5149A-T | BRUSHLESS DC MOTOR CONTROLLER, 2.5 A, PQFP64 |
| TDA5149G-T | DISK DRIVE MOTOR CONTROLLER, 2.5 A, PQFP64 |
| TDA5231 | SPECIALTY CONSUMER CIRCUIT, PDSO28 |
| TDA5230 | SPECIALTY CONSUMER CIRCUIT, PDSO28 |
| TDA5330T-T | 3-BAND, VIDEO TUNER, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TDA5141 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Brushless DC motor drive circuit |
| TDA5141A | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Brushless DC motor drive circuit |
| TDA5141AT | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Brushless DC motor drive circuit |
| TDA5141T | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Brushless DC motor drive circuit |
| TDA5142 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Brushless DC motor drive circuit |
发布紧急采购，3分钟左右您将得到回复。