参数资料
型号: TDA7567PDTR
厂商: STMICROELECTRONICS
元件分类: 音频/视频放大
英文描述: AUDIO AMPLIFIER, PDSO36
封装: ROHS COMPLIANT, SOP-36
文件页数: 7/30页
文件大小: 346K
代理商: TDA7567PDTR
TDA7567PD
Diagnostics functional description
Doc ID 16903 Rev 1
3.3
Output DC offset detection
Any DC output offset exceeding ±2 V are signalled out. This inconvenient might occur as a
consequence of initially defective or aged and worn-out input capacitors feeding a DC
component to the inputs, so putting the speakers at risk of overheating.
This diagnostic has to be performed with low-level output AC signal (or Vin = 0).
The test is run with selectable time duration by microprocessor (from a "start" to a "stop"
command):
START = Last reading operation or setting IB1 - D5 - (OFFSET enable) to 1
STOP = Actual reading operation
Excess offset is signalled out if persistent throughout the assigned testing time. This feature
is disabled if any overloads leading to activation of the short-circuit protection occurs in the
process.
3.4
AC diagnostic
It is targeted at detecting accidental disconnection of tweeters in 2-way speaker and, more
in general, presence of capacitively (AC) coupled loads.
This diagnostic is based on the notion that the overall speaker's impedance (woofer +
parallel tweeter) will tend to increase towards high frequencies if the tweeter gets
disconnected, because the remaining speaker (woofer) would be out of its operating range
(high impedance). The diagnostic decision is made according to peak output current
thresholds, and it is enabled by setting (IB2-D2) = 1.
Two different detection levels are available:
High current threshold IB2 (D7) = 0
Iout > 500 mApk = NORMAL STATUS
Iout < 300 mApk = OPEN TWEETER
Low current threshold IB2 (D7) = 1
Iout > 250 mApk = NORMAL STATUS
Iout < 125 mApk = OPEN TWEETER
To correctly implement this feature, it is necessary to briefly provide a signal tone (with the
amplifier in "play") whose frequency and magnitude are such to determine an output current
higher than 500 mApk with IB2(D7)=0 (higher than 250 mApk with IB2(D7)=1) in normal
conditions and lower than 250 mApk with IB2(D7)=0 (lower than 125 mApk with IB2(D7)=1)
should the parallel tweeter be missing.
The test has to last for a minimum number of 3 sine cycles starting from the activation of the
AC diagnostic function IB2<D2>) up to the I2C reading of the results (measuring period). To
confirm presence of tweeter, it is necessary to find at least 3 current pulses over the above
thresholds over all the measuring period, else an "open tweeter" message will be issued.
The frequency / magnitude setting of the test tone depends on the impedance
characteristics of each specific speaker being used, with or without the tweeter connected
(to be calculated case by case). High-frequency tones (> 10 kHz) or even ultrasonic signals
are recommended for their negligible acoustic impact and also to maximize the impedance
module's ratio between with tweeter-on and tweeter-off.
相关PDF资料
PDF描述
TDA7567PD AUDIO AMPLIFIER, PDSO36
TDA7571 250 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64
TDA7575BPDTR 50 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO36
TDA7575BPD 50 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO36
TDA7575B 50 W, 2 CHANNEL, AUDIO AMPLIFIER, ZFM27
相关代理商/技术参数
参数描述
TDA7569BLV 功能描述:Amplifier IC 4-Channel (Quad) Class AB 27-Flexiwatt (Vertical) 制造商:stmicroelectronics 系列:- 包装:管件 零件状态:有效 类型:AB 类 输出类型:4-通道(四路) 不同负载时的最大输出功率 x 通道数:50W x 4 @ 4 欧姆 电压 - 电源:6 V ~ 18 V 特性:静音,短路和热保护 安装类型:通孔 工作温度:-40°C ~ 105°C(TA) 供应商器件封装:27 Flexiwatt(垂直) 封装/外壳:27 Flexiwatt(成型引线) 标准包装:17
TDA7570 制造商:STMicroelectronics 功能描述:AUD AMP SPKR 1CH MONO/2CH STEREO 250W/70W CLS-AB 64PIN HI-QU - Trays
TDA7571 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:STPDACsw - Fully digital high efficiency power audio amplifier
TDA7572 功能描述:音频放大器 200W Mono Bridge PWM Amplifier Built-In RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
TDA7572TR 功能描述:音频放大器 200W Mono Bridge PWM Amplifier Built-In RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel