参数资料
型号: TDA7575BPDTR
厂商: STMICROELECTRONICS
元件分类: 音频/视频放大
英文描述: 50 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO36
封装: ROHS COMPLIANT, SOP-36
文件页数: 21/32页
文件大小: 487K
代理商: TDA7575BPDTR
Diagnostics functional description
TDA7575B
Doc ID 14103 Rev 2
Table 10.
Double fault table for turn-on diagnostic
S. GND (so) / S. GND (sk) in the above table make a distinction according to which of the 2
outputs is shorted to ground (test-current source side= so, test-current sink side = sk). More
precisely, in both the channels SO = CH+, and SK = CH-.
In permanent diagnostic the table is the same, with only a difference concerning open load
(*), which is not among the recognizable faults. Should an open load be present during the
device's normal working, it would be detected at a subsequent turn-on diagnostic cycle (i.e.
at the successive car radio turn-on).
7.6
Faults availability
All the results coming from I2C bus, by read operations, are the consequence of
measurements inside a defined period of time. If the fault is stable throughout the whole
period, it will be sent out. This is true for DC diagnostic (turn-on and permanent), for offset
detector.
To guarantee always resident functions, every kind of diagnostic cycles (turn-on, permanent,
offset) will be reactivate after any I2C reading operation. So, when the micro reads the I2C, a
new cycle will be able to start, but the read data will come from the previous diag. cycle (i.e.
The device is in turn-on state, with a short to GND, then the short is removed and micro
reads I2C. The short to GND is still present in bytes, because it is the result of the previous
cycle. If another I2C reading operation occurs, the bytes do not show the short). In general
to observe a change in diagnostic bytes, two I2C reading operations are necessary.
7.7
I2C programming/reading sequences
A correct turn on/off sequence respectful of the diagnostic timings and producing no audible
noises could be as follows (after battery connection):
Turn-on: (Standby OUT + DIAG enable) --- 500 ms (min) --- muting OUT
Turn-off: Muting IN --- 20 ms --- (DIAG disable + standby IN)
Car radio installation: DIAG enable (write) --- 20 0ms --- I2C read (repeat until all faults
disappear).
Offset test: device in play (no signal)
Offset enable - 30 ms - I2C reading
(repeat I2C reading until high-offset message disappears).
S. GND (sc)
S. GND (sk)
S. Vs
S. Across L.
Open L.
S. GND (sc)
S. GND
S. Vs + S.
GND
S. GND
S. GND (sk)
/
S. GND
S. Vs
S. GND
Open L. (*)
S. Vs
/
S. Vs
S. Across L.
/
S. Across L.
N.A.
Open L.
/
Open L. (*)
相关PDF资料
PDF描述
TDA7575BPD 50 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO36
TDA7575B 50 W, 2 CHANNEL, AUDIO AMPLIFIER, ZFM27
TDA7575 50 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO36
TDA758013TR SPECIALTY CONSUMER CIRCUIT, PQFP64
TDA7580 SPECIALTY CONSUMER CIRCUIT, PQFP64
相关代理商/技术参数
参数描述
TDA7575PD 功能描述:音频放大器 INFOTAINMENT S PWR RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
TDA7575PDTR 功能描述:音频放大器 INFOTAINMENT S PWR RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
TDA7576B 制造商:STMicroelectronics 功能描述:Dual bridge MOSFET power amplifier for 24V systems
TDA7577BLV 功能描述:Amplifier IC 2-Channel (Stereo) Class AB 27-Flexiwatt (Vertical) 制造商:stmicroelectronics 系列:- 包装:管件 零件状态:有效 类型:AB 类 输出类型:2 通道(立体声) 不同负载时的最大输出功率 x 通道数:45W x 2 @ 4 欧姆 电压 - 电源:6 V ~ 18 V 特性:静音,短路保护,待机 安装类型:通孔 工作温度:-40°C ~ 105°C(TA) 供应商器件封装:27 Flexiwatt(垂直) 封装/外壳:27 Flexiwatt(成型引线) 标准包装:17
TDA7577LV 制造商:STMicroelectronics 功能描述:ABD AUDIO & POWER - Rail/Tube 制造商:STMicroelectronics 功能描述:Dual BTL output pwr amplifier for 24 V