参数资料
型号: TDA8706AMDB
厂商: NXP SEMICONDUCTORS
元件分类: ADC
英文描述: 3-CH 6-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO24
封装: PLASTIC, SOT-340-1, SSOP-24
文件页数: 7/24页
文件大小: 206K
代理商: TDA8706AMDB
1996 Jul 30
15
Philips Semiconductors
Product specication
6-bit analog-to-digital converter
with multiplexer and clamp
TDA8706A
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our
“IC Package Databook” (order code 9398 652 90011).
Reow soldering
Reflow soldering techniques are suitable for all SO and
SSOP packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250
°C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45
°C.
Wave soldering
SO
Wave soldering techniques can be used for all SO
packages if the following conditions are observed:
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
The longitudinal axis of the package footprint must be
parallel to the solder flow.
The package footprint must incorporate solder thieves at
the downstream end.
SSOP
Wave soldering is not recommended for SSOP packages.
This is because of the likelihood of solder bridging due to
closely-spaced leads and the possibility of incomplete
solder penetration in multi-lead devices.
If wave soldering cannot be avoided, the following
conditions must be observed:
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave)
soldering technique should be used.
The longitudinal axis of the package footprint must
be parallel to the solder flow and must incorporate
solder thieves at the downstream end.
Even with these conditions, only consider wave
soldering SSOP packages that have a body width of
4.4 mm, that is SSOP16 (SOT369-1) or
SSOP20 (SOT266-1).
METHOD (SO AND SSOP)
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260
°C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150
°C within
6 seconds. Typical dwell time is 4 seconds at 250
°C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Repairing soldered joints
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300
°C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320
°C.
相关PDF资料
PDF描述
TDA8764AHL/6/C1 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP32
TDA8764ATS/6/C1 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28
TDA8775GB-S TRIPLE, PARALLEL, WORD INPUT LOADING, 0.01 us SETTLING TIME, 10-BIT DAC, PQFP48
TDA8775G/C1,151 TRIPLE, PARALLEL, WORD INPUT LOADING, 0.01 us SETTLING TIME, 10-BIT DAC, PQFP48
TDF8704T/4D-T 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO24
相关代理商/技术参数
参数描述
TDA8706AMDB-T 功能描述:视频模拟/数字化转换器集成电路 6 BIT INTERFACE RoHS:否 制造商:Texas Instruments 输入信号类型:Differential 转换器数量:1 ADC 输入端数量:4 转换速率:3 Gbps 分辨率:8 bit 结构: 输入电压:3.3 V 接口类型:SPI 信噪比: 电压参考: 电源电压-最大:3.45 V 电源电压-最小:3.15 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:TCSP-48 封装:Reel
TDA8706T 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:6-bit analog-to-digital converter with multiplexer and clamp
TDA8707 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Triple RGB 6-bit video analog-to-digital interface
TDA8707H 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Triple RGB 6-bit video analog-to-digital interface
TDA8708 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Video analog input interface