- 您现在的位置：买卖IC网 > PDF目录85416 > TDA8765H/4/C1 (NXP SEMICONDUCTORS) 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP44 PDF资料下载
参数资料
| 型号： | TDA8765H/4/C1 |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | ADC |
| 英文描述： | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP44 |
| 封装： | PLASTIC, SOT-307-2, QFP-44 |
| 文件页数： | 2/24页 |
| 文件大小： | 205K |
| 代理商： | TDA8765H/4/C1 |
1999 Jan 06
10
Philips Semiconductors
Preliminary specication
10-bit high-speed Analog-to-Digital
Converter (ADC)
TDA8765
Notes
1. The circuit has two clock inputs: CLK and CLK. There are four modes of operation:
a) PECL mode 1 (DC level varies equal to DC level of VCCD): CLK and CLK inputs are at differential PECL levels.
b) PECL mode 2 (DC level varies equal to DC level of VCCD): CLK input is at PECL level and sampling is taken on
the falling edge of the clock input signal. A DC level of 3.65 V has to be applied on CLK decoupled to GND via a
100 nF capacitor.
c) PECL mode 3 (DC level varies equal to DC level of VCCD): CLK input is at PECL level and sampling is taken on
the rising edge of the clock input signal. A DC level of 3.65 V has to be applied on CLK decoupled to GND via a
100 nF capacitor.
d) AC driving mode 4: when driving the CLK input directly and with any AC signal of minimum 0.5 V (p-p) and with
a DC level of 2.5 V, the sampling takes place at the falling edge of the clock signal.
When driving the CLK input with the same signal, sampling takes place at the rising edge of the clock signal. It is
recommended to decouple the CLK or CLK input to DGND via a 100 nF capacitor.
2. It is possible with an external reference connected to pin Vref to adjust the ADC input range. This voltage has to be
referenced to VCCA. For VCCA 1.825 V, the differential input voltage amplitude is 2 V (p-p).
3. The
3 dB analog bandwidth is determined by the 3 dB reduction in the reconstructed output, the input being a
full-scale sine wave.
4. THD (total harmonic distortion) is obtained with the addition of the first five harmonics:
where F is the fundamental harmonic referenced at 0 dB for a full-scale sine wave input.
5. Effective number of bits are obtained via a Fast Fourier Transform (FFT). The calculation takes into account all
harmonics and noise up to half of the clock frequency (Nyquist frequency). Conversion to SNR:
SNR = Nbit × 6.02 + 1.76 dB.
6. Intermodulation measured relative to either tone with analog input frequencies of 4.43 and 4.53 MHz. The two input
signals have the same amplitude and the total amplitude of both signals provides full-scale to the converter (
6dB
below full scale for each input signal).
d3 is the ratio of the RMS-value of either input tone to the RMS-value of the worst case third order intermodulation
product.
7. Output data acquisition: the output data is available after the maximum delay of td.
Timing (CL = 10 pF); see Fig.5 and note 7
td(s)
sampling delay time
2ns
th
output hold time
4
ns
td
output delay time
VCCO = 5.25 V
10
15
ns
VCCO = 3.0 V
13
18
ns
3-state output delay times; see Fig.6
tdZH
enable HIGH
14
18
ns
tdZL
enable LOW
16
20
ns
tdHZ
disable HIGH
16
20
ns
tdLZ
disable LOW
14
18
ns
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
THD
20 log
F
(2nd)
2
(3rd)
2
(4th)
2
(5th)
2
(6th)
2
+
+++
---------------------------------------------------------------------------------------------------------------
=
相关PDF资料 |
PDF描述 |
|---|---|
| TDA8702T/C2 | PARALLEL, 8 BITS INPUT LOADING, 0.065 us SETTLING TIME, 8-BIT DAC, PDSO16 |
| TDA8752AH/6/C4 | 3-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP100 |
| TDA8752AH/8/C4/S1 | 3-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP100 |
| TDA8752AH8BA-S | 3-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP100 |
| TDA8752AH8BA | 3-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TDA8766 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:10-bit high-speed 2.7 to 5.25 V analog-to-digital converter |
| TDA8766G | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:10-bit high-speed 2.7 to 5.25 V analog-to-digital converter |
| TDA8766G/C1,118 | 功能描述:模数转换器 - ADC 10BIT ADC 2.7V RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| TDA8766G/C1,151 | 功能描述:模数转换器 - ADC 10 BIT 3V A/D CONVERTER RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| TDA8766G/C1118 | 制造商:NXP Semiconductors 功能描述: |
发布紧急采购，3分钟左右您将得到回复。