- 您现在的位置：买卖IC网 > PDF目录150819 > TDA8786AGB (NXP SEMICONDUCTORS) SPECIALTY ANALOG CIRCUIT, PQFP48 PDF资料下载
参数资料
| 型号： | TDA8786AGB |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP48 |
| 封装： | PLASTIC, LQFP-48 |
| 文件页数： | 9/31页 |
| 文件大小： | 186K |
| 代理商： | TDA8786AGB |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
1997 Nov 17
17
Philips Semiconductors
Product specication
10-bit analog-to-digital interface for
CCD cameras
TDA8786; TDA8786A
Table 1
Serial interface programming (see note 1)
Note
1. At the end of each programming sequence (usually during the video vertical blanking), the soft clipper register must
be reloaded (for example if the soft clipper is not used, code 15 must be entered in the soft clipper register at the end
of each TDA8786(A) programming sequence).
Table 2
Standby selection
ADDRESS BITS
DATA BITS D9 to D0
A2
A1
A0
0
OFDOUT output control (D7 to D0).
0
1
Soft clipper control. Only the 4 LSBs (D3 to D0) are used. Bits D9 to D4 should be set to
logic 0.
0
1
0
AGC gain control (D8 to D0).
0
1
Partial standby controls for power consumption optimization. Only the 4 LSBs (D3 to D0)
are used. Bits D9 to D4 should be set to logic 0:
D0 = 1: CDS + AGC + soft clipper block in standby; ICCA +ICCD =48mA
D1 = 1: optical black clamp + blanking block in standby; ICCA +ICCD =92mA
D2 = 1: OFD DAC in standby; ICCA +ICCD =98mA
D3 = 1: 6 dB amplifier (output on AMPOUT pin) in standby; ICCA +ICCD = 98.5 mA.
1
0
Clamp reference DAC (D9 to D0).
STDBY
D9 to D0
ICCA +ICCD
1
LOW
4 mA (typ.)
0
active
99 mA (typ.)
相关PDF资料 |
PDF描述 |
|---|---|
| TQD100YGE-A1V | 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| TLV809L30DBVT | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| TPS3126E18DBVT | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| TLV431BCDCKRG4 | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 1.24 V, PDSO6 |
| TWR-5/3-15/250-D24N | 3-OUTPUT 22 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TDA8786G | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:10-bit analog-to-digital interface for CCD cameras |
| TDA8787 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:10-bit, 3.0 V analog-to-digital interface for CCD cameras |
| TDA8787A | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:10-bit, 3.0 V, up to 25 Msps analog-to-digital interface for CCD cameras |
| TDA8787AHL | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:10-bit, 3.0 V, up to 25 Msps analog-to-digital interface for CCD cameras |
| TDA8787AHL/C3,118 | 功能描述:电信线路管理 IC 10-BIT CCD 25MSPS RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。