- 您现在的位置：买卖IC网 > Datasheet目录365 > TDGL004 (Microchip Technology)BOARD CEREBOT 32MX7 PIC32MX795 Datasheet资料下载
参数资料
| 型号： | TDGL004 |
| 厂商： | Microchip Technology |
| 文件页数： | 18/19页 |
| 文件大小： | 0K |
| 描述： | BOARD CEREBOT 32MX7 PIC32MX795 |
| 设计资源： | Cerebot 32MX7 Schematics |
| 标准包装： | 1 |
| 系列： | PIC® 32MX |
| 类型： | MCU |
| 适用于相关产品： | PIC32MX795F512 |
| 所含物品： | 板 |
Cerebot 32MX7 Reference Manual
J20
JP1 &
JP2
JP3 &
JP4
JP5
JP6
JP7
JP8
JP9
JP10
JP17
JA-JF
JPA –
USB Host Connector
This is a standard sized USB type A connector. This connector is used to connect USB
devices to the board when using the PIC32MX795 microcontroller to implement an
embedded USB host.
CAN or Pmod Select
These jumpers select microcontroller signals RF12 and RF13 for use with CAN #1 or Pmod
connector JF. Place these jumpers in the CAN position to use CAN #1. Place the jumpers in
the PMOD position to use then with Pmod connector JF.
Pull-up enable for I2C port #2
These two jumpers are used to enable/disable the pull-up resistors on I2C port #2. Insert
shorting blocks on these two jumpers to enable the pull-up resistors. Remove the shorting
blocks to disable the pull-up resistors. Only a single device on the I2C bus should have the
pull-up resistors enabled.
CAN #1 Termination
This jumper is used to enable/disable the 120 ohm termination resistor for CAN #1. Insert the
shorting block to enable the termination resistor, remove it to disable the termination resistor.
CAN #1 5V0 Enable
This jumper is used to enable/disable providing 5V to the CAN #1 connector. Insert the
shorting block to connect the board 5V0 supply to pins 9 & 10 of CAN #1 connector. Remove
the shorting block to disconnect the 5V0 supply.
CAN #2 Termination
This jumper is used to enable/disable the 120 ohm termination resistor for CAN #2. Insert the
shorting block to enable the termination resistor, remove it to disable the termination resistor.
CAN #1 5V0 Enable
This jumper is used to enable/disable providing 5V to the CAN #1 connector. Insert the
shorting block to connect the board 5V0 supply to pins 9 & 10 of CAN #1 connector. Remove
the shorting block to disconnect the 5V0 supply.
Do Not Use
USB host power select
This jumper is used to select which host connector is powered when host power is enabled.
Place the shorting block in the “MICRO” position to supply power to the USB micro-AB OTG
Connector, J19. Place the shorting block in the “A” position to supply power to the USB type
A Host Connector, J20.
Do Not Use
Pmod Connectors
These connectors provide access to the I/O pins on the PIC32MX795 microcontroller.
Digilent Pmod peripheral modules can be attached to these connectors.
Pmod header power select
www.digilentinc.com
page 18 of 19
Copyright Digilent, Inc. All rights reserved. Other product and company names mentioned may be trademarks of their respective owners.
相关PDF资料 |
PDF描述 |
|---|---|
| TEACLIPPER-PIC-HV-PT | PROGRAMMER TEACLIPPER/PIC HI-V |
| TJA1010T/N1,118 | IC OCTAL LOW SIDE DRVR 28SOIC |
| TLC5945PWP | IC LED DRIVER LINEAR 28-TSSOP |
| TLD1020-12 | POWER SUPPLY 20W 12VDC 1.66A |
| TLD1020-24-C0350 | POWER SUPPLY 20W 12-24VDC .350A |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TDGL005 | 功能描述:子卡和OEM板 chipKIT Basic I/O Shield RoHS:否 制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| TDGL006 | 功能描述:界面开发工具 chipKIT Network Shield RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| TDGL007 | 功能描述:开发板和工具包 - PIC / DSPIC DIGILENT CEREBOT MC7 MOTOR CONTROL BRD RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压: |
| TDGL008 | 功能描述:开发板和工具包 - PIC / DSPIC Digilent Cerebot MX3ck Dev Brd RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压: |
| TDGL009 | 功能描述:开发板和工具包 - PIC / DSPIC Digilent Cerebot MX4cK Dev Brd RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压: |
发布紧急采购，3分钟左右您将得到回复。