- 您现在的位置：买卖IC网 > PDF目录98210 > TEA2260 (STMICROELECTRONICS) 2.5 A SWITCHING CONTROLLER, 100 kHz SWITCHING FREQ-MAX, PDIP16 PDF资料下载
参数资料
| 型号： | TEA2260 |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 稳压器 |
| 英文描述： | 2.5 A SWITCHING CONTROLLER, 100 kHz SWITCHING FREQ-MAX, PDIP16 |
| 封装： | BATWING, PLASTIC, DIP-16 |
| 文件页数： | 8/11页 |
| 文件大小： | 127K |
| 代理商： | TEA2260 |
Obsolete
Product(s)
- Obsolete
Product(s)
TEA2261/0
6/11
GENERAL DESCRIPTION
The TEA2260/61 is an off-line switch mode power
supply controller. The synchronization function
and the specific operation in stand-by mode make
it well adapted to video applications such as TV
sets, VCRs, monitors, etc..
The TEA2260/61 can be used in two types of ar-
chitectures:
– Master/Slave architecture. In this case, the
TEA2260/61 drives the power transistor accord-
ing to the pulse width modulated signals generat-
ed by the secondary located master circuit. A
pulse transformer provides the feedback (see
Figure 1).
– Conventional architecture with linear feedback
signal (feedback sources: optocoupler or trans-
former winding) (see Figure 2).
Using the TEA2260/61, the stand-by auxiliary
power supply, often realized with a small but costly
50Hz transformer, is no longer necessary. The
burst mode operation of the TEA2260/61 makes
possible the control of very low output power
(down to less than 1W) with the main power trans-
former.
When used in a master/slave architecture, the
TEA2260/61 and also the power transistor turn-off
can be easily synchronized with the line transform-
er. The switching noise cannot disturb the picture
in this case.
As an S.M.P.S. controller, the TEA2260/61 fea-
tures the following functions:
– Power supply start-up (with soft-start)
– PWM generator
– Direct power transistor drive (+1.2A, -2.0A)
– Safety functions: pulse by pulse current limita-
tion, output power limitation, over and under volt-
age lock-out.
S.M.P.S. OPERATING DESCRIPTION
Starting Mode - Stand By Mode
Power for circuit supply is taken from the mains
through a high value resistor before starting. As
long as VCC of the TEA2260/61 is below VCC start,
the quiescent current is very low (typically 0.7mA)
and the electrolytic capacitor across VCC is linearly
charged. When VCC reaches VCC start (typically
10.3V), the circuit starts, generating output pulses
with a soft-starting. Then the SMPS goes into the
stand-by mode and the output voltage is a per-
centage of the nominal output voltage (e.g. 80%).
To do this, the TEA2260/61 contains all the func-
tions required for primary mode regulation: a fixed
frequency oscillator, a voltage reference, an error
amplifier and a pulse width modulator (PWM).
For transmission of low power with a good efficien-
cy in stand-by, an automatic burst generation sys-
tem is used, in order to avoid audible noise.
Normal Mode (Secondary Regulation)
The normal operating of the TV set is obtained by
sending to the TEA2260/61 regulation pulses gen-
erated by a regulator located in the secondary side
of the power supply.
This architecture uses the “Master/Slave Con-
cept”, advantages of which are now well-known
especially the very high efficiency in Stand-by
mode, and the accurate regulation in Normal
mode.
Stand-by mode or normal mode are obtained by
supplying or not the secondary regulator. This can
be ordonnered for example by a microprocessor in
relation with the remote control unit.
Regulation pulses are applied to the TEA2260/61
through a small pulse-transformer to the IN input
(Pin 2). This input is sensitive to positive square
pulses. The typical threshold of this input is 0.85V.
The frequency of pulses coming from the second-
ary regulator can be lower or higher than the fre-
quency of the starting oscillator.
The TEA2260/61 has no soft-starting system
when it receives pulses from the secondary. The
soft-start must be located in the secondary regula-
tor.
Due to the principle of the primary regulation, puls-
es generated by the starting system automatically
disappear when the voltage delivered by the
SMPS increases.
Stand-by Mode - Normal Mode Transition
During the transition there are simultaneously
pulses coming from the primary and secondary
regulators.
These signals are not synchronized and some
care has to be taken to ensure the safety of the
switching power transistor.
A very sure and simple way consist in checking the
transformer demagnetization state.
– A primary pulse is taken in account only if the
transformer is demagnetized after a conduction
of the power transistor required by the secondary
regulator.
– A secondary pulse is taken in account only if the
transformer is demagnetized after a conduction
of the power transistor required by the primary
regulator.
With this arrangement the switching safety area of
the power transistor is respected and there is no
risk of transformer magnetization.
1
相关PDF资料 |
PDF描述 |
|---|---|
| TEA3718DP | STEPPER MOTOR CONTROLLER, 1.5 A, PDIP16 |
| TEA3718SP | STEPPER MOTOR CONTROLLER, 1.5 A, PZFM15 |
| TEA5040S | SPECIALTY CONSUMER CIRCUIT, PDIP42 |
| TEA5040 | SPECIALTY CONSUMER CIRCUIT, PDIP40 |
| TEA5551TD | AM, AUDIO SINGLE CHIP RECEIVER, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TEA2261 | 功能描述:视频 IC SMPS Controller RoHS:否 制造商:Fairchild Semiconductor 工作电源电压:5 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-28 封装:Reel |
| TEA2261_03 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:SWITCH MODE POWER SUPPLY CONTROLLER |
| TEA2262 | 功能描述:电流型 PWM 控制器 SMPS Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| TEA2R2M1CTR-0512P | 功能描述:铝质电解电容器 - 带引线 16V 2.2uF 20% RoHS:否 制造商:Kemet 引线类型: 电容:220 uF 容差:20 % 电压额定值:25 V 工作温度范围: 端接类型:Radial 外壳直径:8 mm 外壳长度:11 mm 引线间隔:5 mm 产品:General Purpose Electrolytic Capacitors 封装:Bulk |
| TEA2R2M1HBK-0512P | 功能描述:铝质电解电容器 - 带引线 50V 2.2uF 20% RoHS:否 制造商:Kemet 引线类型: 电容:220 uF 容差:20 % 电压额定值:25 V 工作温度范围: 端接类型:Radial 外壳直径:8 mm 外壳长度:11 mm 引线间隔:5 mm 产品:General Purpose Electrolytic Capacitors 封装:Bulk |
发布紧急采购，3分钟左右您将得到回复。