参数资料
型号: THS3111IDRG4
厂商: TEXAS INSTRUMENTS INC
元件分类: 音频/视频放大
英文描述: 1 CHANNEL, VIDEO AMPLIFIER, PDSO8
封装: GREEN, PLASTIC, SOIC-8
文件页数: 8/37页
文件大小: 980K
代理商: THS3111IDRG4
_
+
THS3110
RF
1 k
49.9
0.1
F
6.8
F
-VS
-15 V
RG
50
Source
+
VI
0.1
F
6.8
F
+
+VS
15 V
49.9
50
LOAD
1 k
SLOS422E – SEPTEMBER 2003 – REVISED OCTOBER 2009........................................................................................................................................ www.ti.com
APPLICATION INFORMATION
MAXIMUM SLEW RATE FOR REPETITIVE
SIGNALS
The THS3110 and THS3111 are recommended for
high slew rate pulsed applications where the internal
nodes of the amplifier have time to stabilize between
pulses. It is recommended to have at least 20-ns
delay between pulses.
The THS3110 and THS3111 are not recommended
for applications with repetitive signals (sine, square,
sawtooth, or other) that exceed 900 V/
μs. Using the
part in these applications results in excessive current
draw from the power supply and possible device
damage.
For applications with high slew rate, repetitive signals,
the THS3091 and THS3095 (single), or THS3092 and
THS3096 (dual) are recommended.
Figure 51. Wideband, Noninverting Gain
Configuration
WIDEBAND, NONINVERTING OPERATION
The THS3110 and THS3111 are unity-gain stable,
Current-feedback amplifiers are highly dependent on
100-MHz, current-feedback operational amplifiers,
the feedback resistor RF for maximum performance
designed to operate from a ±5-V to ±15-V power
and stability. Table 1 shows the optimal gain setting
supply.
resistors RF and RG at different gains to give
maximum bandwidth with minimal peaking in the
Figure 51 shows the THS3111 in a noninverting gain
frequency response. Higher bandwidths can be
of 2-V/V configuration typically used to generate the
achieved, at the expense of added peaking in the
performance
curves.
Most
of
the
curves
were
frequency response, by using even lower values for
characterized using signal sources with 50-
source
RF.
Conversely,
increasing
RF
decreases
the
impedance,
and
with
measurement
equipment
bandwidth, but stability is improved.
presenting a 50-
load impedance.
Table 1. Recommended Resistor Values for
Optimum Frequency Response
THS3110 AND THS3111 RF AND RG VALUES FOR MINIMAL PEAKING WITH RL = 100
GAIN (V/V)
SUPPLY VOLTAGE (V)
RG ()
RF ()
±15
1.5 k
1
±5
1.5 k
±15
1 k
2
±5
1.15 k
±15
200
806
5
±5
200
806
±15
66.5
604
10
±5
66.5
604
±15
1 k
–1
±5
1 k
–2
±15 and ±5
549
1.1 k
–5
±15 and ±5
182
909
–10
±15 and ±5
64.9
649
16
Copyright 2003–2009, Texas Instruments Incorporated
Product Folder Link(s): THS3110 THS3111
相关PDF资料
PDF描述
THS3111CDG4 1 CHANNEL, VIDEO AMPLIFIER, PDSO8
THS3111IDG4 1 CHANNEL, VIDEO AMPLIFIER, PDSO8
THS3111IDGNG4 1 CHANNEL, VIDEO AMPLIFIER, PDSO8
THS3110CDR 1 CHANNEL, VIDEO AMPLIFIER, PDSO8
THS3110CD 1 CHANNEL, VIDEO AMPLIFIER, PDSO8
相关代理商/技术参数
参数描述
THS3112 制造商:BB 制造商全称:BB 功能描述:LOW-NOISE, HIGH-SPEED CURRENT FEEDBACK AMPLIFIERS
THS3112CD 功能描述:高速运算放大器 Dual Lo-Noise High Output Current RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
THS3112CDDA 功能描述:高速运算放大器 Dual Lo-Noise High Output Current RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
THS3112CDDAG3 功能描述:高速运算放大器 Dual Lo-Noise High Output Current RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
THS3112CDDAR 功能描述:高速运算放大器 Dual Lo-Noise High Output Current RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube