- 您现在的位置：买卖IC网 > PDF目录98225 > THS4211DRBTG4 (TEXAS INSTRUMENTS INC) 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 PDF资料下载
参数资料
| 型号： | THS4211DRBTG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| 封装： | GREEN, PLASTIC, SON-8 |
| 文件页数： | 21/47页 |
| 文件大小： | 1197K |
| 代理商： | THS4211DRBTG4 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页
DIE
Side View (a)
DIE
End View (b)
Thermal
Pad
Bottom View (c)
P
D +
Tmax * TA
q
JA
where
PD = Maximum power dissipation of THS4211 (watts)
TMAX = Absolute maximum junction temperature (150°C)
TA = Free-ambient temperature (°C)
θJA = θJC + θCA
θJC = Thermal coefficient from junction to the case
θCA = Thermal coefficient from the case to ambient air
(
°C/W).
Single or Dual
68 Mils x 70 Mils
(Via Diameter = 13 Mils)
SLOS400E – SEPTEMBER 2002 – REVISED SEPTEMBER 2009 ................................................................................................................................... www.ti.com
The PowerPAD package represents a breakthrough
transfer. Therefore, the holes under the THS4211
in combining the small area and ease of assembly of
and THS4215 PowerPAD package should make
surface
mount
with
the
heretofore
awkward
their connection to the internal ground plane, with
mechanical methods of heatsinking.
a
complete
connection
around
the
entire
circumference of the plated-through hole.
6. The top-side solder mask should leave the
terminals of the package and the thermal pad
area with its five holes exposed. The bottom-side
solder mask should cover the five holes of the
thermal pad area. This prevents solder from
being pulled away from the thermal pad area
during the reflow process.
7. Apply solder paste to the exposed thermal pad
Figure 89. Views of Thermally
area and all of the IC terminals.
Enhanced Package
8. With these preparatory steps in place, the IC is
simply placed in position and run through the
Although there are many ways to properly heatsink
solder
reflow
operation
as
any
standard
the PowerPAD package, the following steps illustrate
surface-mount component. This results in a part
the recommended approach.
that is properly installed.
For a given
θJA, the maximum power dissipation is
PowerPAD PCB LAYOUT CONSIDERATIONS
shown in Figure 91 and is calculated by Equation 6:
1. Prepare the PCB with a top side etch pattern as
shown in Figure 90. There should be etching for
the leads as well as etch for the thermal pad.
(6)
The next consideration is the package constraints.
Figure 90. PowerPAD PCB Etch and
The two sources of heat within an amplifier are
Via Pattern
quiescent power and output power. The designer
should
never
forget
about
the
quiescent
heat
2. Place five holes in the area of the thermal pad.
generated within the device, especially multi-amplifier
These holes should be 13 mils in diameter. Keep
devices. Because these devices have linear output
them small so that solder wicking through the
stages (Class AB), most of the heat dissipation is at
holes is not a problem during reflow.
low output voltages with high output currents.
3. Additional vias may be placed anywhere along
The other key factor when dealing with power
the thermal plane outside of the thermal pad
dissipation is how the devices are mounted on the
area. They help dissipate the heat generated by
PCB. The PowerPAD devices are extremely useful
the THS4211 and THS4215 IC. These additional
for heat dissipation. But, the device should always be
vias may be larger than the 13-mil diameter vias
soldered to a copper plane to fully use the heat
directly under the thermal pad. They can be
dissipation properties of the PowerPAD. The SOIC
larger because they are not in the thermal pad
package, on the other hand, is highly dependent on
area to be soldered, so wicking is not a problem.
how it is mounted on the PCB. As more trace and
4. Connect all holes to the internal ground plane.
copper area is placed around the device,
θJA
5. When connecting these holes to the ground
decreases
and
the
heat
dissipation
capability
plane, do not use the typical web or spoke via
increases. For a single package, the sum of the RMS
connection methodology. Web connections have
output currents and voltages should be used to
a high thermal resistance connection that is
choose the proper package.
useful for slowing the heat transfer during
soldering operations. This resistance makes the
soldering of vias that have plane connections
easier. In this application, however, low thermal
resistance is desired for the most efficient heat
28
Copyright 2002–2009, Texas Instruments Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| THS4221DBV | 1 CHANNEL, VIDEO PREAMPLIFIER, PDSO5 |
| THS4221DGKG4 | 1 CHANNEL, VIDEO PREAMPLIFIER, PDSO8 |
| THS4221DGNG4 | 1 CHANNEL, VIDEO PREAMPLIFIER, PDSO8 |
| THS4221DGKRG4 | 1 CHANNEL, VIDEO PREAMPLIFIER, PDSO8 |
| THS4221DBVTG4 | 1 CHANNEL, VIDEO PREAMPLIFIER, PDSO5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| THS4211DRG4 | 功能描述:高速运算放大器 Super-Fast Ultr-Lo- Distortion Hi-Speed RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| THS4211EVM | 功能描述:放大器 IC 开发工具 THS4211 Eval Mod RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| THS4211EVM-UG | 功能描述:放大器 IC 开发工具 THS4211 Eval Mod w/ Unity Gain RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| THS4215 | 制造商:TI 制造商全称:Texas Instruments 功能描述:LOW-DISTORTION HIGH-SPEED VOLTAGE FEEDBACK AMPLIFIER |
| THS4215D | 功能描述:高速运算放大器 Super-Fast Ultr-Lo- Distortion Hi-Speed RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。