- 您现在的位置：买卖IC网 > PDF目录98226 > THS4271DRG4 (TEXAS INSTRUMENTS INC) 1 CHANNEL, VIDEO PREAMPLIFIER, PDSO8 PDF资料下载
参数资料
| 型号： | THS4271DRG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 1 CHANNEL, VIDEO PREAMPLIFIER, PDSO8 |
| 封装： | GREEN, PLASTIC, SOIC-8 |
| 文件页数： | 20/48页 |
| 文件大小： | 1227K |
| 代理商： | THS4271DRG4 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
_
+
Rf
4kT = 1.6E-20J
at 290K
THS4271/THS4275
IBN
EO
ERF
RS
ERS
IBI
Rg
ENI
4kTRS
4kT
Rg
4kTRf
E
O +
E 2
NI
) IBNRS
2
) 4kTRS NG
2 ) IBIRf
2
) 4kTRfNG
E
O
+
E 2
NI
) IBNRS
2
) 4kTRS )
I
BIRf
NG
2
)
4kTR
f
NG
-3
-2.5
-2
-1.5
-1
-0.5
0
0.5
1 M
10 M
100 M
f - Frequency - Hz
Normalized
Gain
-
dB
FREQUENCY RESPONSE
vs
CAPACITIVE LOAD
RL = 499
VS =±5 V
R(ISO) = 25 CL = 10 pF
R(ISO) = 15 CL = 100 pF
R(ISO) = 10 CL = 50 pF
www.ti.com
SLOS397F – JULY 2002 – REVISED OCTOBER 2009
additional pole in the signal path that can decrease
the phase margin. When the primary considerations
are frequency response flatness, pulse response
fidelity, or distortion, the simplest and most effective
solution is to isolate the capacitive load from the
feedback loop by inserting a series isolation resistor
between the amplifier output and the capacitive load.
This does not eliminate the pole from the loop
response, but rather shifts it and adds a zero at a
higher frequency. The additional zero acts to cancel
the phase lag from the capacitive load pole, thus
increasing the phase margin and improving stability.
The Typical Characteristics show the recommended
isolation resistor vs capacitive load and the resulting
Figure 87. Noise Analysis Model
frequency response at the load. Parasitic capacitive
loads greater than 2 pF can begin to degrade the
The total output spot noise voltage can be computed
performance of the THS4271. Long PCB traces,
as the square of all square output noise voltage
unmatched cables, and connections to multiple
contributors. Equation 4 shows the general form for
devices can easily cause this value to be exceeded.
the output noise voltage using the terms shown in
Always consider this effect carefully, and add the
recommended series resistor as close as possible to
the THS4271 output pin (see the Board Layout
Guidelines section).
(4)
The criterion for setting this R(ISO) resistor is a
maximum bandwidth, flat frequency response at the
Dividing this expression by the noise gain [NG=(1+
load. For a gain of +2, the frequency response at the
Rf/Rg)] gives the equivalent input-referred spot noise
output pin is already slightly peaked without the
voltage at the noninverting input, as shown in
capacitive load, requiring relatively high values of
R(ISO) to flatten the response at the load. Increasing
the noise gain also reduces the peaking.
(5)
Evaluation of these two equations for the circuit and
component values shown in Figure 75 will give a total
output spot noise voltage of 12.2 nV/
√Hz and a total
equivalent input spot noise voltage of 6.2 nV/
√Hz.
This includes the noise added by the resistors. This
total input-referred spot noise voltage is not much
higher
than
the
3-nV/
√Hz
specification
for
the
amplifier voltage noise alone.
Driving Capacitive Loads
One of the most demanding, and yet very common,
load conditions for an op amp is capacitive loading.
Often, the capacitive load is the input of an A/D
converter, including additional external capacitance,
which may be recommended to improve A/D linearity.
Figure 88. Isolation Resistor Diagram
A high-speed, high open-loop gain amplifier like the
THS4271 can be very susceptible to decreased
stability and closed-loop response peaking when a
capacitive load is placed directly on the output pin.
When the amplifier open-loop output resistance is
considered,
this
capacitive
load
introduces
an
Copyright 2002–2009, Texas Instruments Incorporated
27
相关PDF资料 |
PDF描述 |
|---|---|
| THS4271DGNR | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS4271DGN | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS4271DRBR | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS4271DR | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS4271D | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| THS4271-EP | 制造商:TI 制造商全称:Texas Instruments 功能描述:LOW NOISE, HIGH SLEW RATE, UNITY GAIN STABLE VOLTAGE FEEDBACK AMPLIFIER |
| THS4271EVM | 功能描述:放大器 IC 开发工具 THS4271 Eval Mod RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| THS4271EVM-UG | 功能描述:放大器 IC 开发工具 THS4271 Eval Module w/ Unity Gain RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| THS4271MDGNREP | 功能描述:高速运算放大器 Mil Enhance Stable Voltage Feedback Amp RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| THS4271MDGNTEP | 制造商:TI 制造商全称:Texas Instruments 功能描述:LOW NOISE, HIGH SLEW RATE, UNITY GAIN STABLE VOLTAGE FEEDBACK AMPLIFIER |
发布紧急采购，3分钟左右您将得到回复。