- 您现在的位置：买卖IC网 > PDF目录98228 > THS5651AIDW (TEXAS INSTRUMENTS INC) PARALLEL, WORD INPUT LOADING, 0.035 us SETTLING TIME, 10-BIT DAC, PDSO28 PDF资料下载
参数资料
| 型号： | THS5651AIDW |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | DAC |
| 英文描述： | PARALLEL, WORD INPUT LOADING, 0.035 us SETTLING TIME, 10-BIT DAC, PDSO28 |
| 封装： | PLASTIC, SOIC-28 |
| 文件页数： | 11/33页 |
| 文件大小： | 948K |
| 代理商： | THS5651AIDW |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
THS5651A
10BIT, 125 MSPS, CommsDAC
DIGITALTOANALOG CONVERTER
SLAS260A FEBRUARY 2000 REVISED SEPTEMBER 2002
19
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
analog current outputs
Figure 32 shows a simplified schematic of the current source array output with corresponding switches.
Differential PMOS switches direct the current of each individual PMOS current source to either the positive
output node IOUT1 or its complementary negative output node IOUT2. The output impedance is determined
by the stack of the current sources and differential switches, and is typically >300 k
in parallel with an output
capacitance of 5 pF.
Output nodes IOUT1 and IOUT2 have a negative compliance voltage of 1 V, determined by the CMOS process.
Beyond this value, transistor breakdown may occur, resulting in reduced reliability of the THS5651A device. The
positive output compliance depends on the full-scale output current IOUTFS and positive supply voltage AVDD.
The positive output compliance equals 1.25 V for AVDD = 5 V and IOUTFS = 20 mA. Exceeding the positive
compliance voltage adversely affects distortion performance and integral nonlinearity. The optimum distortion
performance for a single-ended or differential output is achieved when the maximum full-scale signal at IOUT1
and IOUT2 does not exceed 0.5 V (e.g. when applying a 50-
doubly terminated load for 20 mA full-scale output
current). Applications requiring the THS5651A output (i.e., OUT1 and/or OUT2) to extend its output compliance
should size RLOAD accordingly.
AVDD
Current Source Array
IOUT1
IOUT2
RLOAD
Current
Sources
Switches
Figure 32. Equivalent Analog Current Output
Figure 33(a) shows the typical differential output configuration with two external matched resistor loads. The
nominal resistor load of 50
will give a differential output swing of 2 VPP when applying a 20-mA full-scale output
current. The output impedance of the THS5651A depends slightly on the output voltage at nodes IOUT1 and
IOUT2. Consequently, for optimum dc integral nonlinearity, the configuration of Figure 33(b) should be chosen.
In this IV configuration, terminal IOUT1 is kept at virtual ground by the inverting operational amplifier. The
complementary output should be connected to ground to provide a dc current path for the current sources
switched to IOUT2. Note that the INL/DNL specifications for the THS5651A are measured with IOUT1
maintained at virtual ground. The amplifier’s maximum output swing and the DAC’s full-scale output current
determine the value of the feedback resistor RFB. Capacitor CFB filters the steep edges of the THS5651A current
output, thereby reducing the operational amplifier slew-rate requirements. In this configuration, the op amp
should operate on a dual supply voltage due to its positive and negative output swing. Node IOUT1 should be
selected if a single-ended unipolar output is desirable.
相关PDF资料 |
PDF描述 |
|---|---|
| THS5651AIPWR | PARALLEL, WORD INPUT LOADING, 0.035 us SETTLING TIME, 10-BIT DAC, PDSO28 |
| THS5651AIPWRG4 | PARALLEL, WORD INPUT LOADING, 0.035 us SETTLING TIME, 10-BIT DAC, PDSO28 |
| THS5651AIPW | PARALLEL, WORD INPUT LOADING, 0.035 us SETTLING TIME, 10-BIT DAC, PDSO28 |
| THS5651AIDWR | PARALLEL, WORD INPUT LOADING, 0.035 us SETTLING TIME, 10-BIT DAC, PDSO28 |
| THS5651AIPWG4 | PARALLEL, WORD INPUT LOADING, 0.035 us SETTLING TIME, 10-BIT DAC, PDSO28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| THS5651AIDWG4 | 功能描述:数模转换器- DAC 10-Bit 100MSPS Comms DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| THS5651AIDWR | 功能描述:数模转换器- DAC 10-Bit 100MSPS Comms DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| THS5651AIDWRG4 | 功能描述:数模转换器- DAC 10-Bit 100MSPS Comms DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| THS5651AIPW | 功能描述:数模转换器- DAC 10-Bit 100MSPS Comms DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| THS5651AIPWG4 | 功能描述:数模转换器- DAC 10-Bit 100MSPS Comms DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。