- 您现在的位置：买卖IC网 > PDF目录136933 > THS7001CPWPRG4 (TEXAS INSTRUMENTS INC) SPECIALTY ANALOG CIRCUIT, PDSO20 PDF资料下载
参数资料
| 型号： | THS7001CPWPRG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| 封装： | GREEN, PLASTIC, HTSSOP-20 |
| 文件页数： | 8/41页 |
| 文件大小： | 1203K |
| 代理商： | THS7001CPWPRG4 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
THS7001, THS7002
70MHz PROGRAMMABLEGAIN AMPLIFIERS
SLOS214C OCTOBER 1998 REVISED MARCH 2007
16
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
noise calculations and noise figure (continued)
_
+
RF
RS
RG
eRg
eRf
eRs
en
IN+
Noiseless
IN
eni
eno
Figure 52. Noise Model
The total equivalent input noise density (eni) is calculated by using the following equation:
e
ni +
en
2
) IN )
R
S
2
) IN–
R
F
R
G
2
) 4kTRs ) 4kT RF RG
Where:
k = Boltzmann’s constant = 1.380658
× 1023
T = temperature in degrees Kelvin (273 +
°C)
RF || RG = parallel resistance of RF and RG
(1)
To get the equivalent output noise of the amplifier, just multiply the equivalent input noise density (eni) by the
overall amplifier gain (AV).
eno + eni AV + eni 1 )
R
F
R
G
(Noninverting Case)
(2)
As the previous equations show, to keep noise at a minimum, small value resistors should be used. As the
closed-loop gain is increased (by reducing RF + RG), the input noise can be reduced considerably because of
the parallel resistance term. This leads to the general conclusion that the most dominant noise sources are the
source resistor (RS) and the internal amplifier noise voltage (en). Because noise is summed in a
root-mean-squares method, noise sources smaller than 25% of the largest noise source can be effectively
ignored. This can greatly simplify the formula and make noise calculations much easier to calculate.
By using the low noise preamplifiers as the first element in the signal chain, the input signal’s signal-to-noise
ratio (SNR) is maintained throughout the entire system. This is because the dominant system noise is due to
the first amplifier. This can be seen with the following example:
相关PDF资料 |
PDF描述 |
|---|---|
| TXD10005KASLPLNH | 1-OUTPUT 1000 W AC-DC PWR FACTOR CORR MODULE |
| TPS54290PWPR | 4.6 A DUAL SWITCHING CONTROLLER, 360 kHz SWITCHING FREQ-MAX, PDSO16 |
| TC1142-3.5EUART | SWITCHED CAPACITOR REGULATOR, 500 kHz SWITCHING FREQ-MAX, PDSO8 |
| TC54VC3501EZB713 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PBCY3 |
| TLV431AQDBVRQ1 | THREE TERM VOLTAGE REFERENCE, PDSO5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| THS7001EVM | 功能描述:放大器 IC 开发工具 THS7001 Hi-Spd Amp Eval Mod RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| THS7001IPWP | 功能描述:特殊用途放大器 70-MHz Hi-Spd Prog Gain Amplifier RoHS:否 制造商:Texas Instruments 通道数量:Single 共模抑制比（最小值）: 输入补偿电压: 工作电源电压:3 V to 5.5 V 电源电流:5 mA 最大功率耗散: 最大工作温度:+ 70 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-20 封装:Reel |
| THS7001IPWPG4 | 功能描述:特殊用途放大器 70-MHz Hi-Spd Prog Gain Amplifier RoHS:否 制造商:Texas Instruments 通道数量:Single 共模抑制比（最小值）: 输入补偿电压: 工作电源电压:3 V to 5.5 V 电源电流:5 mA 最大功率耗散: 最大工作温度:+ 70 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-20 封装:Reel |
| THS7001IPWPR | 功能描述:运算放大器 - 运放 70 MHz Hi Spd Prog Gain Amplifier RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| THS7001IPWPRG4 | 功能描述:运算放大器 - 运放 70 MHz Hi Spd Prog Gain Amplifier RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。